VBL16R25SFD
Product Specifications
VBL16R25SFD
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBL16R25SFD from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBL16R25SFD: a 600 V super junction switch with a fast body diode
The VBL16R25SFD is an N channel super junction MOSFET in the TO-263 outline with a 600 V drain to source rating, a plus or minus 30 V gate and a body diode described by the vendor as ultra fast. The summary gives 0.110 ohm at a 10 V gate with 8.5 A flowing, a continuous drain current of 25 A with the case at 25 C and 16 A with the case at 100 C, a pulsed rating of 75 A and a single pulse avalanche energy of 1200 mJ. The junction is rated to 150 C, the drain source dV/dt is 50 V per nanosecond, and the reverse diode dV/dt is limited to 15 V per nanosecond.
The part is aimed at the switch mode supplies that run from a rectified mains: server and telecom power, power factor correction, and the ballast and HID lighting supplies that still use a hard switched half bridge. In those circuits the body diode conducts during the dead time on every cycle, and a slow diode turns the recovery loss into heat in the opposite switch. The fast diode and the 40 ns recovery are the feature that separates this part from a general purpose super junction die.
The ratings a buyer checks first
| Drain to source voltage at maximum junction | 600 V |
| Gate to source voltage | plus or minus 30 V |
| On resistance at 10 V gate, 8.5 A | 0.110 ohm typical |
| Continuous drain current, case at 25 C and 100 C | 25 A and 16 A |
| Pulsed drain current | 75 A |
| Single pulse avalanche energy | 1200 mJ from 28.2 mH at 8 A |
| Maximum power dissipation, case at 25 C | 140 W |
| Junction to case and junction to ambient | 0.57 and 62 C per watt |
| Gate threshold at 250 microamp | 2.5 V minimum, 4.5 V maximum |
| Total gate charge at 520 V and 8 A | 42 nC typical |
| Gate source and gate drain charge | 15 and 19 nC typical |
| Input, output and reverse transfer capacitance | 2600, 80 and 4 pF |
| Effective output capacitance, energy and time related | 63 and 213 pF |
| Turn on delay and rise time | 18 and 24 ns typical |
| Turn off delay and fall time | 80 and 12 ns typical |
| Body diode forward drop at 8 A | 1.5 V maximum |
| Body diode reverse recovery time | 40 ns typical |
| Body diode recovered charge and peak current | 5.8 microcoulomb and 30 A at 400 V |
| Drain source dV/dt and reverse diode dV/dt | 50 and 15 V per nanosecond |
| Operating junction and storage range | minus 55 to plus 150 C |
Reading the electrical table instead of the front page
The output capacitance is where a super junction die differs from a planar one, and the difference is not captured by the 80 pF small signal figure. The energy related effective capacitance is 63 pF and the time related one is 213 pF, and the second is three times the first because the capacitance curve is steep near zero volts. In a hard switched half bridge the energy stored in that capacitance is dissipated in the channel of the opposite switch at every turn on, and a buyer who counts only the 80 pF row will under estimate the loss by a factor of three.
The gate charge of 42 nC at 520 V is low for a 600 V part, and the 19 nC of gate drain charge is the number that sets the Miller plateau. A 1 A driver turns the part on in about 40 ns, which matches the printed 24 ns rise with margin. The low charge is what makes a 100 kHz to 200 kHz hard switched converter practical without a resonant tank.
The resistance of 0.110 ohm at 8.5 A gives 8 W of conduction loss, and at 16 A it gives 28 W. With a 0.57 C per watt junction to case the die sits 16 C above a 100 C case at 16 A, which is comfortable; on a bare board at 62 C per watt the same 28 W is not, and the board level current is closer to 3 A for a 100 C rise. The TO-263 body is the thermal route, and the tab has to be soldered to a plane or bolted to a sink.
The diode rows are the reason to pay for this part. A 40 ns recovery and 5.8 microcoulomb recovered at 400 V is fast, and the 30 A peak recovery current is modest enough that the opposite switch does not see a large spike. In a half bridge at 100 kHz the recovery loss is small compared with the conduction loss, which is what allows the dead time to be kept short and the efficiency to stay high at light load.
Where a 600 V super junction part earns its place
The first use is the primary side of a server or telecom power supply between 200 W and 600 W, where the part sits in a hard switched half bridge or a two transistor forward. The 25 A current and the fast diode suit the dead time behaviour, and the low gate charge keeps the drive loss small at 100 kHz.
The second use is a power factor correction stage in continuous conduction mode, where the boost diode is a silicon carbide part and the switch has to recover the charge of its own output capacitance at every turn on. The 63 pF energy related figure is what sets that loss, and the 1200 mJ avalanche rating covers the surge that a lightning test applies to the boost inductor.
The third use is a ballast or an HID igniter, where the part sees a high voltage kick at strike and a continuous square wave afterwards. The 15 V per nanosecond reverse diode limit is the constraint to respect, because the igniter pulse can rise faster than that through the diode.
Sourcing notes and the second source question
Super junction parts are not interchangeable on capacitance, even when the voltage and the resistance match, because the cell structure decides the output capacitance curve and the recovery behaviour. Two 600 V parts at 0.11 ohm can differ by a factor of two in the energy related capacitance, which on a hard switched bridge is the difference between a 10 W and a 20 W turn on loss. The power management cross reference keeps both effective capacitance rows and the diode recovery beside the resistance for that reason.
The gate is rated to plus or minus 30 V, which is wider than the usual 20 V and gives room for a drive that overshoots on a long gate trace. A replacement part with a 20 V gate limit will not survive the same board, so the gate rating belongs in the comparison as much as the resistance does. The how to verify a drop in replacement page lists it in the first pass.
Where a product is in production and the original part is short, the BOM shortage recovery route looks for the same cell in a different package before it looks at a different vendor, because a package change is easier to qualify than a capacitance change.
Questions we answer before a reel is booked
The first question is the dead time. A 40 ns recovery with a 30 A peak current means the opposite switch must not turn on until the recovery is over, and a controller set to a 200 ns dead time is safe while a 50 ns setting is not. We ask for the gate driver and the dead time setting before agreeing that the part fits a bridge.
The second question is the clamp. The 1200 mJ avalanche rating is a single pulse at 8 A from 28.2 mH, and in a power factor correction stage the inductor is much smaller but the current is much larger, so the comparison has to be done on energy at the actual current rather than on the headline number.
The third question is the thermal interface. A 140 W rating with the case at 25 C assumes the tab is held there, and a TO-263 on a plane gives 62 C per watt from junction to ambient. A buyer planning 16 A continuous should plan a sink, and the 25 A figure should be read as the package limit rather than as an operating point.