HXC50073
Product Specifications
HXC50073
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXC50073 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXC50073: 180 W on 28 V for multicarrier base station duty
The HXC50073 is the largest row in the 700 to 1700 MHz part of this shelf: 180 W, internally matched, 28 V, 20 dB of gain and 59 per cent drain efficiency, marked Pulse on the index row. The vendor page describes a 180 W internally matched LDMOS transistor for multicarrier WCDMA, PCS, DCS and LTE base station and ISM applications from 700 to 1700 MHz, used in Class AB, Class B and Class C for all typical cellular base station modulation formats.
That application list is the most demanding on the shelf. Multicarrier base station duty means several modulated carriers at once, a peak to average ratio of six to ten decibels, and a linearity requirement that decides the adjacent channel leakage. A part sold into that socket is a part built for linear operation at backoff, and the 180 W figure is a saturated or near saturated number that the linear use will not reach.
The index marks the row Pulse while the page describes multicarrier continuous duty. That is the sharpest version of a conflict that runs through this shelf, and on this row it is worth resolving before a board is started, because a pulse rated die run continuous at high duty is a thermal question with no published answer.
The HXC50073 rows as the vendor publishes them
| Part class | LDMOS RF power transistor, internally matched |
| Output, index row | 180 W |
| Output in dBm, calculated | 52.55 dBm |
| Voltage at 50 ohm, calculated | 94.9 V rms, 134.2 V peak |
| Peak against the 28 V rail, calculated | 4.79 times, at the connector |
| Frequency range, index row | 1.2 to 1.7 GHz |
| Frequency range, vendor page | 700 to 1700 MHz |
| Drain rail, index row | 28 V |
| Gain, index row | 20 dB |
| Drive required, calculated | 1.8 W, or 32.55 dBm |
| Drain efficiency, index row | 59 per cent |
| DC input at that efficiency, calculated | 305 W, 10.9 A at 28 V |
| Heat to remove, calculated | 125 W |
| Mode, index row | Pulse |
| Duty described on the vendor page | Multicarrier base station modulation formats, continuous in practice |
| Classes on the vendor page | Class AB, Class B and Class C |
| Application list, vendor page | Multicarrier WCDMA, PCS, DCS, LTE base station, ISM |
| Output at 1 dB compression | Not published |
| Peak to average ratio the row is rated for | Not published |
| Adjacent channel leakage at any backoff | Not published |
| Thermal resistance, junction to case | Not published in text |
| Drain to source breakdown | Not published in text |
| Input, output and feedback capacitance | Not published in text |
| Load mismatch tolerance | Not published |
| Junction temperature maximum | Not published in text |
| Package outline | Not published in text |
| Data sheet link on the vendor page | Points at the site root, serves nothing |
| Parameters block on the vendor page | Published as a picture, not as text |
| Orderable addendum | None published |
| Packing quantity and moisture level | Not published |
Multicarrier duty changes the meaning of 180 W
A multicarrier base station signal has a peak to average ratio of six to ten decibels, and the transistor is backed off until the peaks do not compress. A part rated 180 W saturated will run at perhaps 20 to 45 W average in a linear application, which is 55.0 to 46.5 dBm of peak envelope and 43 to 46 dBm average. The heat, however, follows the average plus the inefficiency at backoff, and efficiency at ten decibels of backoff falls to 20 or 25 per cent, so the heat can be higher than at full power.
That is the calculation a base station engineer runs, and none of the numbers needed for it are published here. There is no compression point, no peak to average rating, no adjacent channel figure and no efficiency curve. The only published efficiency is a single 59 per cent figure, which belongs at or near saturation and will not hold at backoff.
So the row can be used for a linear application only after measurement. A two tone test at the intended backoff, with the adjacent channel measured at the intended offset, is the minimum. For a WCDMA or LTE use that test is a standard bench and takes a day, and it is the only way to know whether the part meets a spectral mask.
The 700 to 1700 MHz claim and the 1.2 to 1.7 GHz index
The index row starts at 1.2 GHz and the page claim starts at 700 MHz, a 500 MHz gap that is 2.5 to 1 in frequency. For an internally matched part that is a large extension, and the same gap appears on the 45 W row next to it on this shelf. The most likely reading is that the vendor matches to 1.2 to 1.7 GHz for the higher power and can reach 700 MHz at reduced performance, but nothing on either page says so.
A buyer interested in 900 MHz should treat the part as unproven there and ask for a test. A buyer interested in 1.8 to 2.1 GHz, which is the PCS and LTE band the page names, is outside the index band as well, and that is a second reason to ask: the page claims coverage of bands the index does not list on either side.
For a use inside 1.2 to 1.7 GHz the pages agree and the row can be treated as a 180 W part with 20 dB of gain. That covers the 1.4 GHz and 1.5 GHz trunking and satellite bands, and it is the safe part of the claim.
Twenty decibels and 1.8 W of drive at 180 W
Twenty decibels of gain at 180 W means 1.8 W of drive, which is a single small stage. That is a considerable advantage over the 1000 W row on the same shelf, which needs 100 W, and it is the reason a 180 W amplifier can be built as a two device chain with a compact driver.
The current is 10.9 A at 59 per cent efficiency, which is a normal 28 V supply and a normal bulk capacitor. At 45 per cent efficiency, the current rises to 14.3 A and the heat to 220 W, so the efficiency figure has more leverage here than on the smaller rows. On a linear application at backoff the effective efficiency will be lower still, and the heat sink has to be sized on that number rather than on 125 W.
The peak voltage at the connector is 134 V, and at a 3 to 1 load it is 402 V. On a 28 V rail those figures come from the internal match transforming to a low drain impedance, and they are the numbers that size the output capacitors and the connector. A 200 V part is not enough for the mismatch case.
Where the HXC50073 sits on the shelf
At 700 to 1700 MHz the shelf carries this 180 W row and a 45 W row. The step is 6.02 dB, and there is nothing in between on this shelf, so a requirement of 90 or 100 W in this band has to be met by combining two 45 W parts or by backing off this one. The 40 W row at 1.0 to 2.0 GHz is a different band and a different match.
Read as a choice, this row is for a 28 V multicarrier or ISM transmitter in the 1.2 to 1.7 GHz range that needs 180 W saturated or 20 to 45 W linear, with 1.8 W of drive and a thermal path for 125 to 220 W. A buyer who needs less power takes the 45 W row and gets 68 per cent efficiency and an external match; a buyer who needs more has to combine parts, because the shelf has no larger row in this band.
Before the purchase order goes out
Three procurement points follow. No orderable addendum is published for this row, so the tray quantity, the moisture level and the marking have to come from the vendor in writing before a production order is placed, and the incoming route for a part whose duty description is a modulation format rather than a number is set out on the incoming inspection plan page. Buyers comparing this row against a competitor's 180 W 1.5 GHz part should work from the RF power transistor cross reference, which lines the two up on linearity, gain and package rather than on the headline wattage. A bill of materials that carries the 1.8 W driver, the output passives and the bias components can be placed through the one stop RF supply route.