Contact Us

VBL1401

Brand: VBsemi
VBsemi VBL1401 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBL1401 — Discrete & Power Semiconductors | Superb Automation

VBL1401

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBL1401 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBL1401: 280 A at 40 V in a D2PAK

The VBL1401 is an N channel MOSFET in the D2PAK body, also sold as TO-263, printed at 40 V drain to source and plus or minus 25 V on the gate. On resistance is 1.0 milliohm at a 10 V gate and 1.2 milliohm at 4.5 V, with 280 A at a 25 C case and 220 A at 70 C, and a 750 A pulsed rating. The part is built for one job: carry a lot of current through a surface mount joint without a heatsink, and do it at 40 V so that a 12 V or 24 V bus has room for the transients.

The body is the tab, and the tab is the drain, so the thermal path runs from the die through the copper tab into the board. The sheet gives 0.33 C per watt typical and 0.4 maximum junction to case, which is among the lowest figures in the TO-263 family, and 32 to 40 C per watt junction to ambient on a one inch board. The package limitation is stated plainly: the current is limited by the leads and the joint at 110 A, not by the die.

Ratings and the package limit

Drain to source voltage40 V, 45 V minimum breakdown
Gate to source voltageplus or minus 25 V
On resistance at 10 V gate1.0 milliohm at 30 A
On resistance at 4.5 V gate1.2 milliohm at 20 A
Continuous drain current280 A at 25 C case, 220 A at 70 C case
Ambient current rating229 A at 25 C, 223 A at 70 C
Pulsed drain current750 A
Package limited current110 A
Single pulse avalanche energy320 mJ into 0.1 mH
Power dissipation312 W at 25 C case, 200 W at 70 C case
Junction to case0.33 C per watt typical, 0.4 maximum
Gate threshold voltage1.2 V minimum, 2.5 V maximum
Total gate charge160 nC typical, 260 nC maximum
Input capacitance9335 pF
Body diode recovery50 ns typical, 105 nC maximum recovered charge

Three numbers that disagree with each other

This sheet carries two inconsistencies that a buyer should see rather than discover. The first is the temperature range: the operating junction and storage range is printed as minus 55 C to plus 150 C, while the continuous current row is labelled at a 175 C junction. Both cannot be right. The second is the breakdown voltage: the summary says 40 V and the electrical table prints 45 V minimum. The 45 V row is the measured breakdown and the 40 V is the working rating, which is normal practice, but it does mean the part has more headroom than the front page suggests and less than the 45 V row implies at temperature.

The third is the current column itself. The tab says 280 A at a 25 C case, the notes say the package limits the part to 110 A, and the ambient rows say 229 A at 25 C ambient. Those cannot all describe the same joint. The honest reading is that the die can carry 280 A if the case is held at 25 C by something other than the part, the leads and the solder joint limit the practical continuous current to about 110 A, and the ambient rows assume a copper area that a real board rarely provides. A 110 A figure on a real board is a build that works; 280 A is a number on a page.

One more row deserves attention before a board is committed: the on resistance is quoted at 30 A, not at the 110 A the package can carry. At 110 A the same 1 milliohm produces 12 W in the die, and the junction to case figure of 0.4 C per watt puts the case 5 C above the junction, which is fine only if the copper under the tab is held near ambient. In a sealed enclosure with no airflow the tab heats the board, the board heats the neighbouring parts, and the resistance rises with the junction temperature in the usual way. A current sense resistor in the same path adds its own loss and should be counted at the same time, because the two together usually decide whether the product needs a heatsink.

The gate charge is 160 nC typical and 260 nC maximum, which is a lot. At 100 kHz that is 26 mA of average gate current at the maximum figure, and the driver has to source and sink several amps during the edge. The gate resistance is 0.85 to 1.3 ohm, low enough that the part switches fast and rings if the gate loop is long. This is not a part to drive from a microcontroller pin through a 10 k resistor.

Where 280 A at 40 V belongs

Synchronous rectification on the secondary of a 12 V output converter, battery disconnect on a 24 V pack, and the low side of a high current buck are the three natural homes. Server and telecom power supplies use several in parallel for a 100 A rail, and the low on resistance means the conduction loss at 50 A is 2.5 W per device, which a D2PAK tab can move into the board. Motor drives for small traction and pumps use it as the low side switch where the 750 A pulse covers a stall.

Because the resistance is so low, the part is also a good reverse polarity or ORing switch, with the caveat that the body diode conducts in the blocking direction and the forward drop at 50 A is around 0.9 V, which is 45 W of loss. A back to back pair removes that, at the cost of doubling the resistance and the gate drive. In every use the joint is the limit, so the copper and the solder void rate under the tab matter more than the die.

Sourcing and the joint that decides the rating

TO-263 parts at 1 milliohm are a crowded field and the differences hide in the same rows every time: resistance at 4.5 V, gate charge, avalanche energy and the package limited current. Our pin to pin cross reference puts those four side by side before anything is quoted, because a part with half the gate charge but twice the threshold can be a worse fit than the original. The D2PAK pad is standard, but the tab thickness and the lead bend differ between vendors and both affect solder voiding.

For a second source on a qualified product, the tests in how to verify a drop in replacement are the ones that catch the failures this family produces: a thermal soak at the real current with the tab instrumented, a solder void inspection after reflow, and a short circuit event to confirm the current limit. We supply the part with a per lot resistance sample and a date code record, and the supplier quality audit trail follows the goods, not just the first order.

What buyers ask before committing

Can this part carry 200 A continuously? Not through a TO-263 joint. The package limited figure of 110 A is the number to quote, and anything above that needs several devices in parallel or a different body. The second question is about paralleling: at 1 milliohm the resistance dominates and the sharing is good, but each device needs its own gate resistor and a symmetric source path, otherwise one device takes the current and the others watch.

The third is the gate drive. With 260 nC maximum and a 1 ohm gate resistance, a 4 A driver is the sensible starting point, and the gate loop has to be measured rather than assumed. The fourth is avalanche: 320 mJ into 0.1 mH is generous for a 40 V part, and it will absorb the turn off of a motor without a clamp in most cases, but it is a single pulse at 25 C and it derates with temperature.

On supply, we quote the reel quantity and the date code, and we sample the on resistance and the threshold on each lot. If a customer needs the 45 V breakdown row confirmed on a certificate, that is a measurement we can arrange with the lot, not an assumption from the front page.