Contact Us

VBFB165R05S

Brand: VBsemi
VBsemi VBFB165R05S is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBFB165R05S — Discrete & Power Semiconductors | Superb Automation

VBFB165R05S

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBFB165R05S from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBFB165R05S: 650 V and 5 A in a through hole body

The VBFB165R05S is a single N channel MOSFET rated at 650 V drain to source with a plus or minus 30 V gate window and a threshold of 3.5 V. It carries 5 A and its on resistance is 950 milliohm at a 10 V gate. The silicon is a multi epitaxial super junction structure and the body is the three lead through hole package the vendor page calls TO251 in the table and TO220 in the descriptive text.

A 650 V, 5 A, 950 milliohm part is a small offline converter switch, an auxiliary supply switch, or the pass element in a standby rail. The resistance is the point: at 1 A it drops 0.95 V and dissipates 0.95 watt, which is already more heat than a small converter wants to shed, so the part is normally run at 0.5 A or less in continuous mode and at its 5 A rating only in a pulse.

The gate needs 10 V to reach the published resistance and the gate window allows 30 V, so this is a part driven from a controller with a 12 V or 15 V output, not from a logic pin. A 3.5 V threshold with a 10 V drive gives 6.5 V of overdrive, which is the normal operating point for an offline switch.

Key data for the VBFB165R05S

ConfigurationSingle N channel
PackageThree lead through hole, TO251 in the table and TO220 in the descriptive text, confirm before ordering
VDS650 V
VGSPlus or minus 30 V
Vth3.5 V typical
ID5 A
RDS(on) at 10 V950 milliohm
TechnologyMulti epitaxial super junction
Gate chargeNot published on the catalogue page, and on a super junction part it is the number that decides the drive
Body diodeIntrinsic, with a recovery charge that matters in a flyback
Package noteThe table and the text disagree on the body, and the descriptive text names a different code in the same family

Super junction silicon changes what the gate sees

Super junction devices reach a given resistance with a much smaller die than a planar part of the same voltage, and the price is a higher gate charge for the same die area plus a body diode with a sharper recovery. On a 950 milliohm, 5 A part the gate charge is small in absolute terms, but the switching behaviour is not simply scaled down from a planar part of the same rating.

Two practical consequences. First, the gate resistor has to be chosen from the actual charge, not from a rule of thumb, because a super junction device with a fast gate can ring at the turn on edge and produce radiated noise that a planar part at the same frequency would not. Second, the body diode recovery in a continuous conduction flyback is a real loss, and a part with a fast recovery or a parallel Schottky is sometimes the better choice at the same voltage.

The 30 V gate window is wide for a 650 V part and gives room for the negative excursion that a gate driver sees when the source moves during a turn off. It does not mean the gate can be driven at 30 V; the resistance curve peaks well before that and the drive is normally 10 to 15 V.

Reading 650 V and 5 A as a thermal statement

At 0.5 A the part dissipates about 0.24 watt and the through hole body is far from its limit. At 1 A it dissipates 0.95 watt and the tab rises 40 to 60 degrees above ambient on a modest heatsink. At 2 A it dissipates 3.8 watt and the part needs a real heatsink or forced air. The 5 A rating is a die and bond wire limit, not a continuous operating point.

That arithmetic is why a 950 milliohm part at 650 V is used at half an amp and a 200 milliohm part at the same voltage is used at two amps. Choosing between them is a question of the current the circuit actually needs, not of the rating.

The package ambiguity matters more than it should. A TO251 and a TO220 have different tab widths, different creepage to the heatsink and different mounting hardware, and a board that was laid out for one will not accept the other without a change. The vendor page puts both in the same description, so the body has to be confirmed from the supplier record rather than from the page.

Sourcing a 650 V part with a small current

Parts in this cell are usually chosen once and then held for the life of a product, because a change means re-qualifying the converter and its EMI. That makes availability the first question and the electrical second. Our obsolete part cross reference hub page covers the process we use when a 650 V part reaches end of life and the board cannot be changed.

For a new circuit the comparison points are the gate charge, the body diode recovery and the package, in that order. A part with the same resistance and a heavier gate will run hotter in a flyback even though the DC loss is identical, because the switching loss scales with charge and frequency.

The sourcing side of this part is covered on the strategic sourcing. For a 650 V part that rarely has a true second source, that page covers how the supply is held for the life of the product.

Questions we get on this code

Is the body TO251 or TO220? The catalogue table says TO251 and the descriptive text says TO220. We quote against the string on the request and confirm the body from the supplier record before shipping, because the two do not interchange on a board.

Can it run at 5 A continuously? Not without a heatsink sized for 24 watt. The 5 A figure is a limit, and the continuous current at 950 milliohm is set by the thermal path.

Does it need a gate driver? It needs a 10 to 15 V drive with a defined turn off path. A logic level pin is not enough for a 3.5 V threshold part that is meant to switch an offline rail.

What about avalanche and surge? The catalogue page publishes no avalanche energy figure. A circuit that expects the switch to absorb an inductive surge has to confirm that energy in the data sheet or add a clamp.