Contact Us

VBC8338

Brand: VBsemi
VBsemi VBC8338 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBC8338 — Discrete & Power Semiconductors | Superb Automation

VBC8338

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBC8338 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBC8338: one N channel and one P channel in a single TSSOP-8 body

VBC8338 is a complementary pair from VBsemi: an N channel MOSFET with a 30 V drain source rating and 6.2 A of continuous current, and a P channel with a minus 30 V rating and minus 5 A, both in an eight pin TSSOP body. The pair shares a package and nothing else, so a board gets a low side switch and a high side switch in one placement.

The reason this part exists is the half bridge that is not a half bridge: a level shifter, a load switch with a reverse polarity device, a bidirectional signal switch or a small push pull driver where the two devices never conduct at the same time and therefore never need matched resistances. The N channel is 22 milliohms at 10 V of gate drive and the P channel is 45 milliohms, and the asymmetry is fine for those jobs and wrong for a synchronous converter.

The values below come from the VBsemi datasheet for this string. Where a number is printed only as a typical value we say so, because a purchase decision should not rest on a typical that has no maximum beside it.

What the asymmetry means in practice

At 6 A the N channel dissipates 0.79 W. At 5 A the P channel dissipates 1.13 W, and at 4.5 V of gate drive its resistance rises to 66 milliohms, which at 5 A is 1.65 W. The package is rated for 1.35 W at 25 degrees ambient with 90 degrees per watt junction to ambient, so a P channel carrying 5 A continuously is already past the package limit before any margin is added.

That is not a defect, it is the intended use. A load switch carries current in one direction at a time, and the P channel in a high side switch is on when the N channel is off. A board that needs both devices conducting at 5 A simultaneously wants two single MOSFETs in packages with a thermal pad.

Configurationone N channel and one P channel, independent
N channel rating30 V drain source, 6.2 A continuous at 25 degrees
N channel on resistance22 milliohms at 10 V gate drive, 6 A
N channel threshold1 V to 3 V at 250 microamps
N channel gate charge7 nC typical, 11 nC maximum
N channel capacitances550 pF input, 105 pF output, 90 pF reverse transfer
P channel ratingminus 30 V drain source, minus 5 A continuous at 25 degrees
P channel on resistance45 milliohms at minus 10 V gate drive, 66 milliohms at minus 4.5 V
P channel thresholdminus 1 V to minus 3 V at 250 microamps
P channel gate charge14.4 nC typical, 23 nC maximum
P channel capacitances960 pF input, 190 pF output, 170 pF reverse transfer
Pulsed current20 A N channel, minus 18 A P channel
Power dissipation1.35 W at 25 degrees ambient
Thermal resistance90 degrees per watt junction to ambient on one square inch of copper
Gate source limitplus or minus 20 V both channels
Body diode, N channel1.2 V forward at 1.2 A, 15 ns reverse recovery
Body diode, P channel1.2 V forward at 1.2 A, 19 ns reverse recovery
Junction rangeminus 55 to plus 150 degrees Celsius
PackageTSSOP-8, surface mount
Constructiontrench, RoHS compliant and halogen free

Gate drive and the logic level question

The N channel threshold of 1 V to 3 V means the part turns on somewhere between those points, and a 3.3 V logic output will drive it into the linear region rather than fully on. The datasheet prints the on resistance at 10 V of gate drive, which is the sign that 3.3 V drive gives a resistance higher than 22 milliohms and the part is not characterised there. For a 3.3 V system the honest options are a gate driver with a charge pump or a different part rated at 4.5 V and 2.5 V.

The P channel has the same issue in the other direction: minus 10 V of gate drive is what the 45 milliohm figure assumes, and a P channel driven from a 3.3 V rail through a resistor will sit at minus 3.3 V and read closer to 66 milliohms. A high side switch that has to be efficient at low voltage needs either a charge pump or a P channel with a lower threshold.

Where a complementary pair earns its place

The clean use is a signal level translator with a resistive pull up and a pair of devices, or a bidirectional switch in an analog path where the on resistance is not critical. The second clean use is a load switch with a reverse polarity protection device on the input, where the N channel is the pass device and the P channel is the reverse blocking device.

A third use is a small motor driver for a toy or an appliance damper, where the current is under 1 A and the pair forms a half bridge with two external resistors. At that current the dissipation is tens of milliwatts and the package is comfortable.

The use that disappoints is a synchronous buck converter. The P channel cannot be driven fast enough from a logic pin, its resistance is twice the N channel and its gate charge is twice as large, so the switching losses dominate at any frequency above a hundred kilohertz. A pair built for that job has matched devices and a proper driver.

Supply chain notes for a VBsemi string

VBsemi parts carry their own order codes and their own datasheets, and the strings are not interchangeable with the western parts whose numbers they resemble. A customer who has a BOM line written as a familiar part number and a substitute from this vendor needs the substitution checked pin by pin and parameter by parameter, which is what the power management cross reference page describes.

Where a build is short of a specific MOSFET, the BOM shortage recovery route looks at three things in order: an exact string in stock, a part with the same pinout and equal or better ratings, and a board change. The first is a purchase order, the second is an engineering sign off, and the third is a schedule hit.

Incoming inspection and authenticity

The package is small and the marking is laser etched, so visual inspection proves little. What works is a curve tracer or a test fixture that measures the on resistance at a known gate voltage and the threshold on a sample of five, plus a check of the reel label against the order code. A part that measures 22 milliohms at 10 V and 66 at 4.5 V is the right die; one that measures 40 milliohms at 10 V is a different part in the right body.

The incoming inspection plan page sets out the sample sizes and the measurements we use for discrete parts, and it is worth reading before a first order because the acceptance criteria have to be agreed before the reels arrive.

RoHS and halogen free compliance is stated on the datasheet, and for a product going into Europe the declaration and the material data are the documents an auditor will ask for. We hold both for the strings we stock and can send them with a quotation.

Three questions buyers ask about this string

Can the two channels be used as a half bridge? Only at low voltage and low current, because the P channel cannot be driven from a logic pin without help and its resistance is twice the N channel. For a real half bridge, two N channel parts and a driver are better.

Is 6.2 A a real continuous rating? It is the rating at 25 degrees ambient on one square inch of copper, which is a test board rather than a product board. In a small enclosure treat 3 A as the practical continuous figure.

Is there a second source? Not with this exact pinout and these ratings from another vendor. The realistic route is a different part with a board change, and the cross reference work above is how we establish which one.