VBC1307
Product Specifications
VBC1307
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBC1307 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBC1307: a 30 V N channel in a TSSOP8 body
The VBC1307 is a single N channel MOSFET with a 30 V drain to source rating, a plus or minus 20 V gate window and a threshold of 1.7 V. It carries 10 A and its on resistance is 9 milliohm at a 4.5 V gate and 7 milliohm at 10 V. The die is trench silicon and the body is the eight lead TSSOP that measures about 4.4 by 3 millimetre with a 0.65 mm pitch.
The proportions are the useful part of the description. A 30 V rating with a 7 milliohm die and a 10 A current claim belongs on a 12 V rail, on a 5 V rail, or as the low side device of a synchronous buck that steps 12 V down to a core rail. It is not a 24 V part in any real sense, because a 24 V supply that rings by 25 per cent sits at exactly the rating, and there is no margin left for the switch node overshoot that every buck produces at light load.
There is nothing programmable and nothing protected inside. No charge pump, no current limit, no thermal foldback, no gate clamp beyond the 20 V window. The part is a switch, and every decision about how hard it is driven, how fast it turns and what happens when the load faults sits outside it on the board.
Key data for the VBC1307
| Configuration | Single N channel |
| Package | TSSOP8, 0.65 mm pitch, surface mount |
| VDS | 30 V |
| VGS | Plus or minus 20 V |
| Vth | 1.7 V typical |
| ID | 10 A |
| RDS(on) at 4.5 V | 9 milliohm |
| RDS(on) at 10 V | 7 milliohm |
| Technology | Trench |
| Gate charge | Not on the catalogue page, ask for the data sheet before sizing a driver |
| Body diode | Intrinsic, anode at source |
| Thermal path | Die pad on the lead frame, heat leaves through the drain leads and the board copper |
The 4.5 V column is the one that decides the driver
Between a 4.5 V gate and a 10 V gate the on resistance falls from 9 to 7 milliohm, a little over a fifth. That is a small change by the standards of a 100 V part and a large one for a 30 V logic level device, and it means this die was characterised with a real 4.5 V drive in mind rather than being a 10 V part with an optimistic second column.
What the page does not publish is the curve below 4.5 V. A 1.7 V threshold says the channel is forming at 1.7 V, not that the part reaches a usable resistance there. A 3.3 V gate drive is the obvious question for this class of device, and the answer has to come from the transfer curve in the data sheet. A gate that is 1.2 V above threshold typically sits at three to five times the 4.5 V resistance, which on a 2 A load turns 36 milliwatt into something closer to 150 milliwatt and changes the thermal sum on a small body.
The gate window of 20 V is generous for a 30 V part and it is what allows the device to be driven from a 12 V rail directly through a resistor, without a clamp. Anything above that, including the negative spike that a long gate trace picks up from a switching node, needs a resistor at the gate pin and a short return path.
What the TSSOP8 body can carry, and for how long
The 10 A figure is a package claim made at a case temperature of 25 C with the drain leads tied to a copper area. In a closed plastic box at 60 C ambient, a TSSOP8 with 9 milliohm of channel resistance reaches its practical limit at roughly 2.5 to 3 A continuous, because 3 A through 9 milliohm is 81 milliwatt and the thermal resistance of the body to still air is on the order of 60 to 80 degrees per watt once the lead frame is soldered to a modest pad.
That is not a criticism of the part. It is the arithmetic that separates a catalogue current from a working current. For a load switch that carries 1 A, the device runs cool and the 10 A headline is irrelevant. For a buck low side that carries 4 A of inductor current for a third of the period, the average dissipation is about 48 milliwatt and the part is comfortable. For a linear pass element or a continuous 8 A path, the same body is the wrong choice and a DFN with an exposed pad is the right one.
Two smaller points decide real boards. The eight lead body has a 0.65 mm pitch, so the stencil aperture and the paste volume matter more than they do on a 1.27 mm part. And the drain is the thermal path, which means the copper under the drain leads is part of the rating, not decoration.
Matching this code to a second source
A 30 V, 10 A, 7 milliohm N channel in TSSOP8 is one of the most crowded cells in the whole MOSFET catalogue, so a second source almost always exists. The comparison that matters is not the headline resistance but the gate charge, the threshold window and the body diode recovery, because those three decide whether a board that was tuned around one die behaves the same way with another. Our power management cross reference page sets out how a candidate is checked against the original before anything is offered as a drop in.
For a part that is already on a released board, we start from the package, the pinout and the gate drive the board actually applies, then compare the curves. A part that is 1 milliohm better on paper and 4 nC heavier on gate charge can be worse in a 500 kHz converter, and a part with a lower threshold can turn on from drain to gate noise on a fast switch node. Those are the failure modes we screen for, not the catalogue sort order.
The sourcing side of this part is covered on the pin to pin cross reference. For a replaceable 30 V switch the pinout and the gate threshold decide whether a candidate can drop in.
Questions we get on this code
Can it replace a 30 V part with a higher current rating? Yes if the package, the pinout and the gate charge are compatible. A higher current rating in the same body almost always means a larger die, which means more gate charge and a slower turn off, so the driver and the snubber have to be checked as well as the resistance.
Is 1.7 V threshold safe on a 3.3 V logic pin? Safe is the wrong word. It will turn on, but the resistance at 3.3 V is not published here. Ask for the output characteristic at 3.3 V before committing, and add a gate resistor so the pin current stays inside the driver rating during the Miller plateau.
What should a purchase order say? Part number, package, reel size and date code requirement. For a TSSOP8 the reel is the usual 3000 piece large reel and the smaller 250 piece option exists for prototypes. We confirm the reel size on the quote rather than assuming it.
Do you hold stock? We quote from what is confirmed at the time of the request. For a 30 V logic level part the market is normally liquid, and the honest answer for any specific quantity comes back with the quotation rather than before it.