VBI165R01
Product Specifications
VBI165R01
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBI165R01 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBI165R01: 650 V and 1 A in an SOT89
The VBI165R01 is a single N channel MOSFET rated at 650 V drain to source with a plus or minus 30 V gate window and a threshold of 3.5 V. It carries 1 A and its on resistance is 8000 milliohm at a 4.5 V gate and 6400 milliohm at 10 V. The silicon is planar and the body is the SOT89, the small three lead surface mount package with a tab.
A 650 V part in a body this small is a specific tool. It is the start up switch of an offline supply, the discharge path of a bleeder, the switch in a small auxiliary rail, or the level shift device in a circuit that has to hold off the rectified mains. The 1 A rating and the 6.4 ohm resistance mean it is never a power switch: at 0.1 A it already dissipates 64 milliwatt, and at 0.2 A it is 256 milliwatt in a package that can shed about half a watt.
What makes it useful is the voltage. Six kilohm of resistance is irrelevant if the circuit only ever passes a few milliamps, and 650 V of blocking is the whole reason the part exists.
Key data for the VBI165R01
| Configuration | Single N channel |
| Package | SOT89, three lead surface mount with tab |
| VDS | 650 V |
| VGS | Plus or minus 30 V |
| Vth | 3.5 V typical |
| ID | 1 A |
| RDS(on) at 4.5 V | 8000 milliohm |
| RDS(on) at 10 V | 6400 milliohm |
| Technology | Planar |
| Gate charge | Not published on the catalogue page |
| Body diode | Intrinsic, and at 1 A its forward drop is around a volt |
| Creepage | Small body, so the pad to pad gaps are part of the voltage rating of the assembly |
Six kilohm at 10 V and eight at 4.5 V
The two published resistances differ by 25 per cent, which is a modest gap for a planar high voltage part. The reason is that the channel resistance of a 650 V planar device is dominated by the drift region, not by the channel, so gate voltage has less influence than it does on a 30 V part.
That has a practical consequence for drive. A 10 V gate gives 6.4 kilohm and a 4.5 V gate gives 8 kilohm, and the difference at 50 mA is 52 millivolt, which nobody cares about. So this part can be driven from a low voltage rail without paying a large penalty, and it does not need a dedicated driver. A resistor from a logic pin is often enough, with a zener to hold the gate inside the window if the source moves.
The threshold of 3.5 V is the number to watch. A 3.3 V rail sits below it, so a logic pin at 3.3 V will not turn this part on at all at 25 C, and at high temperature the threshold falls enough that it might, partially. That is the worst kind of behaviour: inconsistent across temperature and unit to unit. The gate should be driven to at least 5 V, and preferably 10 V.
Holding off 650 V in a small body
The electrical rating and the physical spacing are two different things. A SOT89 has about a millimetre between adjacent pads, and at 650 V that gap is a creepage problem on a damp board, whatever the silicon is rated for. Conformal coating, a slot in the board, or a keep out around the part are the normal answers, and they are decided at the board level.
The tab of the SOT89 is the drain, and it is at the high voltage node. Any copper attached to it inherits that potential and has to respect the same spacing to the rest of the circuit. A heatsink or a copper pour under the tab is a 650 V node with a large area, which is exactly the shape that produces corona and tracking.
For a start up circuit the part normally conducts for a short interval at power on and then stays off, so the dissipation is a pulse. For a bleeder it conducts continuously and the current has to be kept small. Both uses are legitimate; neither involves the 1 A rating for more than a transient.
Finding a substitute for a high voltage small part
The cells at 650 V and 1 to 2 A are thinner than the low voltage ones, and the choice usually comes down to the body and the threshold rather than to the resistance. A candidate with a 2 V threshold in the same body would turn on from a 3.3 V pin, which changes the circuit behaviour, so the threshold has to match before anything else. Our pin to pin cross reference page sets out how a candidate is compared against the original when the package has to stay the same.
For a part like this the risk is not the electrical performance, it is the safety spacing. A substitute in a smaller body with the same rating may not have the same creepage, and the assembly inherits whatever the substitute provides.
The sourcing side of this part is covered on the supplier onboarding checklist. For a high voltage part in a small body, that page covers what a new source has to document before the first order.
Questions we get on this code
Can it be driven from a 3.3 V pin? No. The threshold is 3.5 V, so a 3.3 V gate leaves the part off at room temperature and marginal at high temperature. Drive it from 5 V or more.
Is it a power switch? No. At 6.4 kilohm the part is limited to tens of milliamps in continuous use. It is a high voltage blocking element, not a power device.
What about the tab potential? The tab is the drain and sits at the high voltage node. The copper attached to it needs the same spacing as the part itself.
How is it packed? SOT89 normally ships on a 1000 or 2000 piece reel. We confirm the reel size and the date code on the quotation.