Contact Us

VBGQF1806

Brand: VBsemi
VBsemi VBGQF1806 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBGQF1806 — Discrete & Power Semiconductors | Superb Automation

VBGQF1806

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBGQF1806 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBGQF1806: an 80 V N channel in a 3 by 3 DFN with a shielded gate

The VBGQF1806 is a single N channel in a DFN8 measuring 3 by 3 millimetres. It is rated at 80 V, carries 56 A, and prints 11.5 milliohm at a 4.5 V gate against 7.5 milliohm at 10 V. The threshold is 3 V, the gate window is plus or minus 20 V, and the technology is listed as SGT, a shielded gate trench.

Shielded gate construction puts a second electrode below the gate to screen the drain field. The visible effect is a lower gate to drain charge for the same on resistance, which cuts the switching loss in a hard switched converter. The invisible effect is a lower output capacitance ratio, which makes the device easier to keep quiet at turn on.

The 80 V rating is the practical class for a 48 V rail. A 48 V nominal system with 60 V transients and a ten per cent margin lands exactly here, and a 60 V part would be marginal while a 100 V part would give up on resistance for margin that is not needed.

Key data for the VBGQF1806

ConfigurationSingle N channel
PackageDFN8, 3.0 mm by 3.0 mm
VDS80 V
VGSPlus or minus 20 V
Vth3 V
ID56 A
RDS(on) at 4.5 V11.5 milliohm
RDS(on) at 10 V7.5 milliohm
TechnologySGT, shielded gate trench
Thermal pathBottom side pad, soldered to the board copper
Gate drive10 V for full enhancement, 4.5 V usable with a loss penalty
Body diodeIntrinsic, forward drop not printed on the catalogue page

The 3 V threshold and a 4.5 V gate leave little room

With a threshold of 3 V, a 4.5 V gate gives 1.5 V of overdrive, which is enough to reach the printed on resistance but not enough to ignore temperature. The threshold falls by about 2.5 millivolt per degree, so at 100 C it is near 2.7 V and the overdrive is larger, which helps conduction. It also means the device is easier to turn on by accident at high temperature, so the pull down has to be firm.

A 10 V gate is where the 7.5 milliohm figure lives, and the difference against 11.5 milliohm is 35 per cent. On a 20 A load that is 1.6 watt of saving on one device, which decides whether the part runs warm or cool. If the driver can only reach 5 V, budget for the 4.5 V column and size the thermal path for the extra loss rather than assuming the best figure.

The 20 V gate window means a 10 V drive is comfortable and a 12 V drive is still inside, but any ringing above 20 V on the gate destroys the oxide. A 10 ohm gate resistor and a short gate loop are the standard answer.

56 A in a 3 by 3 package is a bond wire number

The 56 A figure is set by the internal clip and the bond wires, not by the silicon. At 56 A and 7.5 milliohm the die dissipates 23.5 watt, which a 3 by 3 DFN cannot pass to the board without a thermal via array and a large copper plane. The junction to case resistance of this package class is around 1 to 2 degrees per watt, so 23.5 watt means a case at 25 C would give a junction at 45 to 70 C, but the case is never at 25 C in a real product.

The practical continuous current for a 3 by 3 DFN on two ounces of copper with vias is between 15 and 25 A, depending on airflow and how much copper the pad gets. Above that the solder joint and the vias become the limit, not the die. A purchase decision that reads the 56 A as a continuous rating will be disappointed on the first thermal test.

The bottom side pad is also the electrical drain. Vias under the pad carry both current and heat, and their count matters. A common failure mode on a first build is a pad with a handful of vias and a part that runs 30 C hotter than the simulation.

Where an 80 V shielded gate part fits

The 48 V telecom rail, the 48 V datacentre bus, a 36 V battery pack for a power tool or an e-bike, and the primary side of an isolated converter are all inside the 80 V window. A hot swap controller on a 48 V backplane uses exactly this class: the part has to hold off the full bus, then carry the inrush for a few milliseconds, then sit at a low resistance for the life of the product.

For a part that sits on a 48 V backplane where a replacement has to be found years later, the power management cross reference page covers what has to match before a substitute is accepted.

The sourcing side of this part is covered on the supplier quality audit. For a 48 V rail part that has to hold off the bus, that page covers what we ask a source to show about consistency and change notice.

Questions we get on this code

Can it be driven directly from a 5 V logic output? It will turn on, but at the 4.5 V column, which is 11.5 milliohm rather than 7.5. For a load above 10 A use a driver that reaches 10 V.

Is SGT different enough to matter? For a hard switched converter at more than 100 kHz, yes. The gate to drain charge is lower than a plain trench of the same on resistance, which cuts the crossover loss. For a slow on off load switch it makes no practical difference.

What continuous current can I expect in still air? Between 15 and 25 A for a well laid out 3 by 3 pad on two ounce copper. Treat 56 A as a pulse figure and check the junction temperature at the real ambient.

Does the body diode need a parallel schottky? In a synchronous converter the diode conducts during dead time. Its forward drop is not printed on the catalogue page, so ask for the data sheet before deciding whether a parallel schottky earns its place.