Contact Us

VBGQA2403

Brand: VBsemi
VBsemi VBGQA2403 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBGQA2403 — Discrete & Power Semiconductors | Superb Automation

VBGQA2403

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBGQA2403 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBGQA2403: a minus 40 V P channel at 3 milliohm in the DFN 5 by 6 body

The VBGQA2403 is a P channel trench MOSFET in the DFN 5 by 6 outline, printed at minus 40 V with plus or minus 20 V on the gate and a 175 C junction. On resistance is 3 milliohm at a minus 10 V gate with 20 A flowing and 4 milliohm at minus 4.5 V with 50 A, rising to 4 milliohm at 125 C and 6 milliohm at 175 C. Continuous drain current is minus 150 A with the case at 25 C and minus 90 A with the case at 100 C, the pulsed rating is minus 450 A, and single pulse avalanche energy is 125 mJ at 79 A peak from 0.1 mH. Input capacitance is 8000 pF and gate charge 66 nC typical.

A P channel at 3 milliohm in a 40 V class is a strong part, and the comparison with its N channel sibling is the useful one: the 40 V N channel in the same body reaches 0.8 milliohm, so the P channel carries 3.75 times the resistance for the same voltage and roughly the same die area. That ratio is the mobility penalty of holes against electrons, and it is why a P channel is chosen for convenience in a high side position rather than for efficiency.

The ratings a buyer checks first

Drain to source voltageminus 40 V
Gate to source voltageplus or minus 20 V
On resistance at minus 10 V gate, minus 20 A, 25 C3 milliohm
On resistance at minus 4.5 V gate, minus 50 A, 25 C4 milliohm
On resistance at 125 C and 175 C4 and 6 milliohm
Continuous drain current, case at 25 Cminus 150 A, package limited
Continuous drain current, case at 100 Cminus 90 A, package limited
Pulsed drain current and diode pulsed currentminus 450 A
Continuous source current through the diodeminus 90 A, package limited
Single pulse avalanche energy and current125 mJ from 0.1 mH, 79 A peak
Power dissipation with the case at 25 C136 W
Junction to ambient, ten second and steady state15 to 18 and 40 to 50 C per watt
Junction to case0.85 C per watt typical, 1.1 maximum
Gate threshold voltage at minus 250 microampminus 1 V minimum, minus 2 V typical, minus 3 V maximum
Drain leakage at minus 30 V, 25 C, 125 C and 175 Cminus 1 microamp, minus 50 and minus 250 microamp maximum
Input, output and reverse transfer capacitance8000, 470 and 225 pF at minus 25 V
Total gate charge, gate source and gate drain66, 13 and 15 nC typical, 70 nC maximum
Turn on delay and rise time21 and 15 ns typical
Turn off delay and fall time35 and 20 ns typical
Diode forward drop at minus 20 Aminus 1 V typical, minus 1.5 V maximum

Reading the electrical table instead of the front page

At minus 150 A the loss is 67.5 W, and at the 175 C resistance of 6 milliohm the same current would dissipate 135 W, which no DFN body can remove. The useful continuous current on a one inch pad is about 31 A, where 2.9 W lifts the junction 115 C above a 60 C ambient. The headline number and the board number differ by a factor of five, and for a P channel that factor is the binding constraint rather than a footnote.

The gate charge is the best row on this sheet. At 66 nC typical and 70 nC maximum it is a third less than the N channel siblings, on a die that is otherwise comparable, and that is a real advantage in a load switch driven from a small charge pump or through a series resistor. The turn on delay of 21 ns and the turn off delay of 35 ns with 15 ns and 20 ns edges are consistent with that charge, and they describe a part that switches cleanly at 100 kHz without a large driver.

The leakage rows are specified at minus 30 V on a minus 40 V part, so a buyer does not get a leakage figure near the blocking limit. For a battery switch that sits at the full rail this is a small gap, and the number to ask for is the leakage at minus 36 V across temperature, particularly because a P channel with the gate at source potential is the state the part sits in whenever the product is off.

The gate threshold window from minus 1 V to minus 3 V is the row that decides the drive. With a minus 4.5 V gate the worst case part has 1.5 V of overdrive and the sheet still prints 4 milliohm, so a 5 V system can drive this part directly. A minus 2.5 V rail cannot, and a buyer planning to drive from a 3.3 V logic output should be aware that the gate has to be pulled below the source by 4.5 V, not to 0 V, which means a level shifter or an open drain driver referenced to the source.

Where a minus 40 V P channel earns its place

The first use is a high side load switch on a 24 V to 36 V rail, where the part has to block in both directions when off, has to turn on without a charge pump and has to survive the inrush into a capacitor bank. The second is a battery disconnect in a 36 V pack, where the switch sits in the positive rail and the gate is pulled down by a small NPN or a comparator.

The third is reverse polarity protection on a 24 V input, where the P channel carries the load current continuously and the 4 milliohm at a minus 4.5 V gate keeps the loss at 1.6 W for a 20 A load on a pad that can take it. The fourth is an ORing element between two 24 V supplies, where two of these back to back give bidirectional blocking with a single gate node.

What the part is not is an efficient synchronous rectifier. At 3.75 times the resistance of its N channel sibling for the same voltage and body, a P channel in a rectifier position wastes three quarters of the available improvement. Where a driver can be afforded, an N channel in the return path beats this part on loss every time.

Sourcing notes and the second source question

A P channel second source has two traps that an N channel comparison does not: the gate has to be referenced to a moving source node, and the body diode points the other way, so a candidate with the same resistance can have a completely different behavior when the load is disconnected. The pin to pin cross reference records the pin order and the diode orientation beside the electrical rows for that reason.

The other comparison is the hot resistance, because two minus 40 V P channels that both print 3 milliohm at 25 C can print 5 and 8 milliohm at 175 C, and in a load switch that runs warm the hot figure sets the pad. The power management cross reference carries both columns.

On the supply side, P channel dies of this class are built in fewer lines than their N channel equivalents and are the first part to disappear when a consumer product ramps. Our obsolete part cross reference hub is where we track a part whose vendor has stopped promoting it but has not yet published an end of life date.

Questions we answer before a reel is booked

The first is the drive reference. The gate has to sit 4.5 V below the source to reach the printed 4 milliohm, and in a high side position the source is the load node. A driver referenced to ground turns the part on hard at start up and lets it fall into linear operation as the load rises, which is the most common way a P channel high side switch fails.

The second is the current on the board. The minus 150 A row assumes a 25 C case with a soldered tab; on a one inch pad the honest figure is about 31 A, and a buyer planning 60 A should show the copper and the airflow.

The third is the diode rating. The continuous source current through the diode is minus 90 A and the diode forward drop is 1 V at 20 A, so a body diode carrying the load during a transient dissipates 20 W to 90 W. The diode is a transient path, not an operating path, and a product that relies on it in steady state has the wrong topology.