VBKB5245
Product Specifications
VBKB5245
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBKB5245 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBKB5245: a complementary pair in an SC70-8 with a very low N side resistance
The VBKB5245 is a dual N plus P part in an eight lead SC70. Both halves are rated at 20 V with a plus or minus 20 V gate window. The N side threshold is 1.0 V and the P side minus 1.2 V. The N channel carries 4 A and the P channel minus 2 A, and the catalogue prints 2 milliohm on the N side at 4.5 V against 23 milliohm on the P side.
That 2 milliohm figure deserves a note. For a 4 A device in an SC70-8, 2 milliohm is far below the usual 20 to 40 milliohm band for this package class, and the same table prints 23 milliohm for the P half of the same die. A number that low points either to a very large die for the package or to a typographical slip in the catalogue. Treat it as unconfirmed until the full data sheet is in hand, and do not size a thermal budget on it.
The rest of the table is consistent: at 10 V the P side comes down from 23 to 14 milliohm, which is the normal trend, while the N side stays at 2. That flatness on the N side is another reason to ask for the curve.
Key data for the VBKB5245
| Configuration | Dual, one N channel plus one P channel |
| Package | SC70-8, eight leads, surface mount |
| VDS | Plus or minus 20 V |
| VGS | Plus or minus 20 V |
| Vth | 1.0 V N channel, minus 1.2 V P channel |
| ID | 4 A N channel, minus 2 A P channel |
| RDS(on) at 4.5 V | 2 milliohm N, 23 milliohm P, N figure to be confirmed on the data sheet |
| RDS(on) at 10 V | 2 milliohm N, 14 milliohm P |
| Technology | Trench |
| Thermal path | One lead frame for both halves |
| Typical use | Signal switch, bidirectional path, battery disconnect |
| Sourcing note | Ask for the data sheet curve before quoting a loss figure to a customer |
Bidirectional conduction and where it helps
A complementary pair with independent drains can be arranged as a bidirectional switch: the two sources are tied together at the mid point, the gates are driven from a common control, and the two drains are the two terminals. In that arrangement the pair conducts in both directions and blocks in both directions, which a single device cannot do because of its body diode.
This is the arrangement used for an analogue signal switch, an audio path switch, or a battery disconnect where the charger and the load share one terminal. The on resistance in that arrangement is the sum of the two halves, so the P side dominates: 23 milliohm in series with the N side, with the loss concentrated in the P half.
The advantage over a dedicated analogue switch is current. A signal switch IC is usually limited to a few hundred milliamps. This pair will carry amps, at the cost of a gate drive that has to be referenced correctly on both halves.
What to check before a reel is accepted
For a part in this package class the first check is the marking. An SC70-8 carries a short code, not the full part number, and two members of a family can share a marking. The second check is the tape orientation, because an eight lead SC70 in an 8 mm tape has a pin one direction that is easy to reverse. The third is the date code against the reel label.
The 2 milliohm entry is a reason for a fourth check: ask the supplier which data sheet revision the reel was made against, and compare the on resistance plot rather than the summary table. A catalogue summary that is one digit off is a real risk in this industry, and it is cheaper to catch it at the receiving dock than in a thermal test.
Where this pair earns a place
Battery disconnect in a handheld product, a signal path that has to be isolated when a module is unplugged, and a small bidirectional load switch on a 5 V or 12 V rail are the three uses that fit. The 20 V rating and the 2 A P side set the ceiling.
For a part whose printed numbers need confirmation, the sourcing route matters. The power management cross reference page covers how a substitute is compared parameter by parameter when the original is unavailable.
The sourcing side of this part is covered on the supplier quality audit. For a part whose printed table needs confirming against the data sheet, that page covers what we check at the source.
Questions we get on this code
Is 2 milliohm realistic for this package? It is unusually low. Ask for the data sheet on resistance curve at 4.5 V and at 25 C before it is used in a loss calculation. If the curve shows 20 milliohm, the table has a typo and the thermal budget changes by a factor of ten.
Can the pair carry 4 A continuously? Not in an SC70-8. At 4 A even a 20 milliohm N side burns 320 milliwatt, which is at the package limit in still air. Plan for 1.5 to 2 A continuous.
What happens if both gates are driven on while the path is bidirectional? The two devices conduct in series and the pair behaves as one resistor of the sum of the two on resistances. That is the intended state for a closed switch.
Does the pair need a separate gate supply? For a bidirectional switch the two gates can be driven from one control if both sources are tied together at the mid point, because the gate to source voltage is the same for both.