Contact Us

VBGQF1302

Brand: VBsemi
VBsemi VBGQF1302 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBGQF1302 — Discrete & Power Semiconductors | Superb Automation

VBGQF1302

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBGQF1302 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBGQF1302: 30 V and 70 A in a DFN 3 by 3

The VBGQF1302 is a single N channel MOSFET rated at 30 V drain to source with a plus or minus 20 V gate window and a threshold of 1.7 V. It carries 70 A and its on resistance is 2.75 milliohm at a 4.5 V gate and 1.8 milliohm at 10 V. The silicon is a shielded gate structure in the DFN 3 by 3 body.

Two milliohm in a three millimetre square package is the sort of number that makes a synchronous buck practical at 30 A per phase. At 20 A the part dissipates 0.72 watt at 1.8 milliohm, which the pad can shed on a normal four layer board without a heatsink. At 40 A it is 2.9 watt and the copper becomes the limit.

The 30 V rating, combined with 1.8 milliohm, places this device on a 12 V rail, a 5 V rail, or the output side of a buck. It is not a 24 V part in a switching position, because the switch node overshoot on a 24 V input with a fast turn off exceeds 30 V unless it is clamped.

Key data for the VBGQF1302

ConfigurationSingle N channel
PackageDFN 3 x 3 mm with exposed pad
VDS30 V
VGSPlus or minus 20 V
Vth1.7 V typical
ID70 A
RDS(on) at 4.5 V2.75 milliohm
RDS(on) at 10 V1.8 milliohm
TechnologyShielded gate trench
Gate chargeNot published on the catalogue page, and at this die size it is the switching budget
Body diodeIntrinsic, and in a buck it carries the inductor current during the dead time
Thermal pathExposed pad on the drain, so the copper island sets the continuous current

A low threshold and a very low resistance pull in opposite directions

The threshold of 1.7 V and the resistance of 1.8 milliohm at 10 V describe a die that is meant to be driven hard. A 1.7 V threshold in a device this fast also means the part is sensitive to gate to drain coupling: at a fast switch node the displacement current through the gate drain capacitance can lift the gate above threshold and turn the device partially on while it should be off.

That is the failure mode that shows up as unexplained heating at light load in a synchronous buck, and it is handled with a gate resistor to ground at the low side device, a driver with an active clamp, or a negative turn off bias. It is not a property of this part alone; every low threshold, low resistance switch in this class has the same issue, and the parts with a higher threshold trade some of the switching speed for immunity.

The gap between 2.75 milliohm at 4.5 V and 1.8 at 10 V is 53 per cent, which is larger than the usual 20 to 30 per cent on a 100 V part. A large gap means the die was characterised with a high gate drive in mind, and a 5 V driven board loses more than half of the advertised performance.

What 70 A means in a three millimetre body

The continuous current is set by the pad, the copper and the air. With the pad soldered to four square centimetres of copper on the component side and a via array to a solid ground plane, the junction to ambient resistance is about 40 degrees per watt. At 20 A and 1.8 milliohm the loss is 0.72 watt and the junction sits 29 degrees above ambient. At 40 A it is 2.9 watt and 116 degrees above ambient, which is outside the range for most products.

The 70 A rating assumes a case at 25 C, which in a real product means a heatsink or a cold plate. For a board with no heatsink the working current is 15 to 25 A, and that should be the number in a thermal budget, not the headline.

The die is large for the body, which has a second consequence: the thermal expansion mismatch between silicon and the lead frame is handled by the package, and a part that runs hot through repeated cycles is where solder fatigue appears first. Keeping the junction swing modest is a reliability decision as much as a thermal one.

Checking this part into a bill of material

For a synchronous buck there are two devices with different jobs. The high side switch is on for a short fraction of the period and its loss is mostly switching, so gate charge matters more than resistance. The low side switch conducts for most of the period and its loss is mostly conduction, so resistance and body diode behaviour matter more. Choosing one code for both positions is a compromise that this part makes well on the low side. Our BOM scrubbing page covers what we check on a released bill of material before a build, including whether the two positions were meant to be the same device.

The parts around the switch matter as much. A 1.7 V threshold device with 1.8 milliohm needs a gate loop measured in millimetres and a driver that can sink several amps at turn off. A board that adds a 10 ohm gate resistor to tame ringing and then runs at 500 kHz will lose more in switching than it gained in conduction.

The sourcing side of this part is covered on the component shortage forecast. For a buck switch that is consumed at a steady rate, that page covers how a shortage is seen before it stops a line.

Questions we get on this code

Is the 70 A continuous? No. Without a heatsink the thermal path limits a DFN 3 by 3 near 15 to 25 A. The 70 A figure is a die limit at a 25 C case.

Can it be driven from 3.3 V? The threshold is 1.7 V, so it will turn on, but the resistance at 3.3 V is not published and will be well above 2.75 milliohm. A 5 V driver is the practical minimum for this die.

Is it suitable for a 24 V input buck? Only with a snubber or a clamp that holds the switch node under 30 V. The rating has no margin for the overshoot of a fast turn off on a 24 V rail.

What about the body diode drop? In a buck the low side diode conducts during the dead time, and its forward drop at 20 A is around 0.8 V for the short interval. That is why the dead time is kept short and why a part with a fast body diode is preferred in a high frequency circuit.