Contact Us

VBQF3211

Brand: VBsemi
VBsemi VBQF3211 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBQF3211 — Discrete & Power Semiconductors | Superb Automation

VBQF3211

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBQF3211 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBQF3211: two 20 V N channels in a 3.3 mm by 3.3 mm DFN

VBQF3211 is a dual N channel MOSFET from VBsemi in a 3.3 mm by 3.3 mm DFN body. Each channel is rated 20 V drain source and 25 A continuous at 25 degrees case, with 12 milliohms at 4.5 V of gate drive, 16 milliohms at 2.5 V and 19 milliohms at 1.8 V. The three drive points are the point of the part: it is characterised all the way down to a 1.8 V logic rail.

The intended applications are printed on the front page: DC to DC converters, notebook system power and point of load supplies. All three run from a 3.3 V or a 5 V rail, need two switches per phase in a buck or two switches for a load switch pair, and have very little board area for the power stage. Two channels in one 3.3 mm body is exactly that requirement.

The numbers below come from the VBsemi datasheet for this string. The gate source limit of plus or minus 8 V is the one to note before a driver is chosen, because it is lower than the 20 V that most discrete parts allow and a 12 V gate drive would damage the part.

Logic level drive, down to 1.8 V

A threshold of 0.4 V to 1.0 V is what makes the 1.8 V column meaningful. At 1.8 V of gate drive the part is fully enhanced with 19 milliohms, so a rail powered from a 1.8 V logic supply can switch its own load without a charge pump. At 2.5 V it is 16 milliohms and at 4.5 V it is 12, so the curve flattens above 4.5 V and there is little to gain from a higher drive.

The absolute gate limit of 8 V is the constraint. A 5 V rail plus ringing can reach 8 V at the gate on a fast edge, so the gate resistor and the loop inductance matter more here than on a 20 V gate part. A driver with a 5 V output and a 2.2 ohm gate resistor is a reasonable starting point for a 20 A load.

Configurationtwo independent N channel MOSFETs
Drain source rating20 V per channel
Gate source limitplus or minus 8 V
On resistance at 4.5 V12 milliohms at 10 A
On resistance at 2.5 V16 milliohms at 9 A
On resistance at 1.8 V19 milliohms at 8.2 A
Continuous current25 A at 25 degrees case, per channel
Gate threshold0.4 V to 1 V at 250 microamps
Transconductance47 siemens at 10 V and 10 A
Total gate charge at 4.5 V12 nC typical, 18 nC maximum
Total gate charge at 10 V21 nC typical, 32 nC maximum
Gate source charge2 nC
Gate drain charge1.3 nC
Input capacitance1220 pF at 10 V and 1 MHz
Output capacitance180 pF
Reverse transfer capacitance80 pF
Turn on delay1.8 ns typical, 3.6 ns maximum
Body diode forward voltage0.81 V typical, 1.2 V maximum at 8 A
Body diode reverse recovery20 ns typical, 15 nC typical charge
Junction to case4.3 degrees per watt typical, 5.4 maximum
Junction to ambient38 degrees per watt typical on one square inch of copper
Junction rangeminus 55 to plus 150 degrees Celsius
PackageDFN 3.3 mm by 3.3 mm, eight pins with thermal pad

The loss arithmetic for a point of load stage

At 10 A and 12 milliohms one channel dissipates 1.2 W. With a junction to case resistance of 4.3 degrees per watt the die sits 5 degrees above the case, and the case sits perhaps 30 degrees above the board in still air with a good pad. That puts the junction at about 60 degrees in a 25 degree room, well inside the 150 degree limit, so a single channel at 10 A is comfortable.

Two channels at 10 A each in the same body is 2.4 W and the thermal path is shared, so the case rise roughly doubles and the junction approaches 100 degrees. Still inside the limit, and it is where a synchronous buck with two phases or a dual load switch lives. Above that the part is the wrong size and a 5 by 6 body is the answer.

Why two channels in one body

A synchronous buck needs a high side and a low side switch, and putting them in one package removes one placement, one reel and a few millimetres of trace. The trace is not cosmetic: at 20 A and 100 kHz the loop between the two switches carries the pulsed current, and shortening it reduces the ringing that a fast edge produces. The 8 V gate limit makes that ringing a real concern, so the package is helping twice.

A load switch pair is the second use. Two independent channels can switch two rails with a common ground, which is what a notebook does with its system rail and its always on rail. The part is characterised at 1.8 V and 2.5 V precisely because those rails exist in a notebook.

Drone and battery powered builds

The 20 V rating suits a 3 cell or 4 cell battery pack with margin, and the 12 milliohm channel at 4.5 V is a good match for a 5 V rail derived from the pack. The low gate charge and the 1.8 V capability make it usable with a small microcontroller pin through a resistor, without a dedicated driver, at currents up to a few amps.

For a drone build the weight and the board area matter more than the last milliohm, and two channels in one 3.3 mm body saves both. The drone and UAV component page collects the parts we hold for that class of build, and the power management cross reference page is where the comparison against a single channel alternative is written down.

Gate drive details that catch people

The 8 V absolute gate limit is the first trap. The second is the threshold spread of 0.4 V to 1 V, which means a part with a low threshold can turn on with gate leakage or with a floating gate during power up. A 10 k pull down on each gate is cheap insurance, and it is the difference between a converter that starts every time and one that occasionally shorts a rail.

The third is the body diode. At 0.81 V and 8 A the diode conducts 6.5 W during a dead time, and a long dead time in a converter built for efficiency will show up as heat in the low side device. Keep the dead time short and let the diode do its job for nanoseconds rather than microseconds.

Supply and incoming checks

The part is a VBsemi string with its own reel and marking, and the practical incoming check is an on resistance measurement at two gate voltages on a sample of five, plus a threshold check. A part that measures 12 milliohms at 4.5 V and 19 at 1.8 V is the right die; one that measures 20 milliohms at 4.5 V is a higher voltage part in the same body.

When the string is on a long lead time, the component lead time solutions page describes the three routes we use, and for a dual MOSFET the most useful is often a buffer against the production forecast rather than a substitute, because a substitute in a 3.3 mm body with a different pinout is a board change.

Three questions buyers ask about this string

Can both channels carry 25 A at once? No. The 25 A is a single channel rating at 25 degrees case. Two channels at 25 A in one body would exceed the package dissipation by a wide margin.

Can it be driven from a 3.3 V microcontroller pin? Yes, at currents up to a few amps, with a gate resistor and a pull down. Above that a driver is needed to keep the switching loss down.

Is a 20 V rating enough for a 4 cell pack? Yes for 16.8 V nominal, with a transient allowance that the pack protection has to enforce. For a 6 cell pack a 30 V part is the right choice.