VBK5213N
Product Specifications
VBK5213N
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBK5213N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBK5213N: a complementary pair in an SC70-6
The VBK5213N packs one N channel and one P channel into a six lead SC70. Both halves are rated at 20 V with a gate window of plus or minus 20 V. The N side has a 1.0 V threshold and the P side minus 1.2 V, both close enough that a single control signal with an inverter stage can drive them in step. The N side carries 3.28 A and the P side minus 2.8 A.
The on resistance is where the two halves part company. At a 2.5 V gate the N side is 110 milliohm and the P side 190. At 4.5 V they are 90 and 155. The ratio is about 1.7 to 1, so the P half burns nearly twice the power for the same current, and the current budget has to follow that.
The purpose of the package is board area. Two discrete parts in SC70 packages would take twice the footprint and twice the placement, and the pair keeps the two halves thermally tied, which matters when they conduct alternately.
Key data for the VBK5213N
| Configuration | Dual, one N channel plus one P channel |
| Package | SC70-6, surface mount |
| VDS | Plus or minus 20 V |
| VGS | Plus or minus 20 V |
| Vth | 1.0 V N channel, minus 1.2 V P channel |
| ID | 3.28 A N channel, minus 2.8 A P channel |
| RDS(on) at 2.5 V | 110 milliohm N, 190 milliohm P |
| RDS(on) at 4.5 V | 90 milliohm N, 155 milliohm P |
| Technology | Trench |
| Thermal path | One lead frame, both halves heat together |
| Matching | Thresholds within 0.2 V of each other in magnitude |
| Typical use | Level shift, small half bridge, bidirectional signal switch |
A complementary pair as a level shifter
The classic use of a matched pair in this package is a level shift between a 1.8 V or 3.3 V logic domain and a higher rail. The N channel takes the logic input at its gate, its drain goes to the gate of the P channel through a pull up, and the P channel switches the high rail. The pair inverts twice, so the output follows the input.
What this arrangement buys is a shift with no driver and no charge pump, at the cost of a propagation delay set by the pull up resistor and the gate capacitance. With a 100 kilo ohm pull up and a few picofarads of gate charge the edge is on the order of a few microseconds. For a signal that switches at kilohertz that is fine, for anything above 100 kHz it is not.
The second use is a small half bridge, where the N side is the low side and the P side is the high side. In that arrangement the pair can drive a solenoid or a small fan from a 12 V rail. The dead time has to be generated by the controller, because the pair has no interlock of its own.
3 A in an SC70-6, and the thermal arithmetic
At 3 A and 90 milliohm the N side dissipates 810 milliwatt. An SC70-6 in still air on a small pad has a junction to ambient resistance of about 250 degrees per watt, so 810 milliwatt raises the junction by 200 degrees. The 3.28 A figure is therefore a pulse rating, not a continuous one.
For continuous operation at 40 C ambient and a 125 C junction limit, the package can dissipate about 340 milliwatt. At 90 milliohm that is 1.9 A on the N side and 1.5 A on the P side. Those are the numbers to plan a load switch around, and they are less than half the headline current.
The shared lead frame means the sum of the two halves matters, not each one. In a half bridge only one half conducts at a time, so the sum is the larger of the two. In a level shifter both can conduct at once, so the losses add and the budget halves again.
Where the pair fits, and the sourcing angle
Portable instruments, small motor drivers, LED strings on a battery rail, and level shifting in a mixed voltage product are the natural home. The 20 V rating keeps it inside a 12 V rail with margin and rules out anything with an inductive kick above 20 V.
For a small pair that carries a signal path rather than the main power, the risk is that the code goes short while the product is still shipping. The power management cross reference page covers what is checked before a substitute is accepted.
The sourcing side of this part is covered on the kitting service. For a pair that is placed next to its gate resistors and clamp diodes, that page covers how the line is kitted.
Questions we get on this code
Can both halves be driven from one pin? No. The N side needs a gate above its source and the P side below its source, so one pin cannot hold both on. A small inverter, or the open drain output of the controller, is what makes the pair work in step.
Why is the P side so much worse? Hole mobility is about a third of electron mobility in silicon, so a P channel of the same die area has a higher resistance. The 1.7 to 1 ratio here is better than most, which suggests the P side was given more area.
What is the maximum switching frequency? Nothing in the part sets it, the drive does. With a 3.3 V logic gate the pair switches in tens of nanoseconds, so 100 kHz to 500 kHz is comfortable once the gate resistors are sized.
Is a 20 V rating enough on a 12 V rail? For a resistive load, yes with 8 V of margin. For an inductive load with a freewheel diode, yes. Without a clamp the switch node can ring above 20 V and the part will fail short.