VB5460
Product Specifications
VB5460
VBsemi — Discrete & Power Semiconductors
Product Overview
The VB5460 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VB5460: an N and a P channel in one SOT23-6 body
The VB5460 is a complementary pair. One N channel and one P channel sit on the same die inside a six lead SOT23. The pair is rated at 40 V drain to source in both polarities, with a gate window of plus or minus 20 V and a threshold of 1.8 V on the N side against minus 1.7 V on the P side. The N channel carries 8 A and the P channel carries 4 A, and the on resistance at a 4.5 V gate is 35 milliohm on the N side against 80 milliohm on the P side.
That asymmetry is the first thing to notice. The two halves are not interchangeable loads. A complementary pair is normally used where a small signal has to switch a higher rail, where a half bridge drives a low power load, or where a battery path needs both a charge and a discharge switch. In all three cases the N side does the heavy lifting and the P side either blocks or sources, so the current budget has to be set by the weaker half.
Nothing about the part is programmable. There is no charge pump, no level shifter and no protection block. What the pair gives is a matched pair of thresholds and one thermal path, which keeps the two halves at the same temperature when they conduct in sequence.
Key data for the VB5460
| Configuration | Dual, one N channel plus one P channel |
| Package | SOT23-6, surface mount, six leads |
| VDS | Plus or minus 40 V |
| VGS | Plus or minus 20 V |
| Vth | 1.8 V N channel, minus 1.7 V P channel |
| ID | 8 A N channel, minus 4 A P channel |
| RDS(on) at 4.5 V | 35 milliohm N, 80 milliohm P |
| RDS(on) at 10 V | 30 milliohm N, 70 milliohm P |
| Technology | Trench |
| Gate charge | Not published on the catalogue page, ask for the data sheet before sizing a driver |
| Body diode | Intrinsic to both halves, direction follows the channel polarity |
| Thermal path | Both halves share the lead frame, so the pair heats together |
The 4.5 V column is the one that matters on a 5 V rail
The catalogue prints on resistance at 4.5 V and at 10 V. On the N side the difference is 35 milliohm against 30, about 17 per cent, and on the P side it is 80 against 70, about 14 per cent. A driver that only reaches 4.5 V therefore loses a sixth of the conduction performance, and the loss lands on the die as heat.
Below 4.5 V the page publishes nothing. A 3.3 V rail driving the gate directly is a common question for this class of part, and the honest answer is that the threshold of 1.8 V says the device will turn on, not that it will reach its rated on resistance. A part with a 1.8 V threshold is usually characterised down to 2.5 V in the full data sheet. Ask for that curve before a 3.3 V rail is committed, because a gate drive that is 0.5 V short can double the conduction loss.
The P side needs the gate pulled below the source, not above it. On a 12 V rail that means a driver, a small N channel pulling the gate down, or a resistor plus a switch. Whatever pulls the gate has to survive the full rail plus the gate window, which is why the 20 V gate rating is quoted separately from the 40 V drain rating.
Set the current budget from the P half, not the N half
The two halves differ by a factor of 2.3 in on resistance at the same gate voltage. At 2 A the N side burns 140 milliwatt and the P side burns 320 milliwatt at a 4.5 V gate. In a SOT23-6 the total dissipation that the leads and the board copper can carry is on the order of half a watt before the junction climbs past 100 C in still air, so the P side reaches that limit at about 2.5 A on its own.
The 8 A and 4 A figures are therefore package claims at a case temperature of 25 C with a good copper pad, not steady state numbers for a closed box. Derate them against the ambient the product actually sees. For a load that draws 3 A continuously, this pair is the wrong choice in this package even though the headline current says 8 A. For a load that draws 1 A and is switched occasionally, it is comfortable.
When the pair is used as a half bridge the two halves never conduct together, so the shared thermal path works in its favour. When it is used as a reverse polarity block and a load switch in series, both halves conduct at once and the dissipation adds. That is the case that catches people out on a first build.
Where this pair earns its place, and the sourcing side
The natural home is a small battery powered product where one rail has to be switched on and off and the same rail also has to be protected against a reversed cell. A second home is a low power half bridge driving a solenoid, a small fan or a piezo pump. A third is a level shift between a 3.3 V logic domain and a 12 V load, where the P side pulls the load up and the N side pulls it down.
For a power switching part that is bought against a fixed bill of material, the sourcing question is usually not the first order but the third. The power management cross reference page covers how a substitute is checked when the original code goes short, and which of the printed parameters have to match before a reel is accepted.
The sourcing side of this part is covered on the one stop BOM sourcing. For a board that carries the pair plus its gate resistors and the passive parts around it, that page covers how the whole release is grouped.
Questions we get on this code
Can the pair be driven from one logic pin? Only with an inverter in between. The N side turns on with a gate above the source and the P side with a gate below it, so a single pin cannot hold both in the same state unless one of them is driven through a small signal stage.
Is the body diode a problem when the load is inductive? The P side body diode conducts in the freewheel direction that a low side N channel would normally handle, and its forward drop is close to 0.8 V. At 2 A that is 1.6 watt of dissipation for the duration of the freewheel interval, which is more than the package can take for long.
What happens if only one half is used? The unused half still sits on the same die and still adds capacitance to the shared substrate. Leaving its gate open is not acceptable, tie the gate to the source through a resistor so it cannot float and turn on.
Can two of these be paralleled for more current? No. Paralleling a complementary pair doubles both halves and doubles the gate charge, and the threshold spread means one half takes the current first. Use a single larger part instead.