Contact Us

VBGP1103

Brand: VBsemi
VBsemi VBGP1103 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBGP1103 — Discrete & Power Semiconductors | Superb Automation

VBGP1103

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBGP1103 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBGP1103: a 100 V 180 A switch in the TO-247 body

The VBGP1103 is an N channel trench MOSFET in the TO-247 outline, printed at 100 V with plus or minus 20 V on the gate and a 175 C junction. On resistance is 3 milliohm at a 10 V gate with 30 A flowing and 4 milliohm at 4.5 V with 60 A, continuous drain current is 180 A with the case at 25 C and 140 A with the case at 70 C, and the pulsed rating is 540 A for 100 microseconds. Gate charge is 105 nC typical, input capacitance 8200 pF, single pulse avalanche energy 1000 mJ at 110 A peak, and the body diode recovers in 40 ns typical.

The TO-247 is the body for a product that dissipates tens of watts and has a metal chassis to bolt to. Where the seven lead TO-263 version of the same die conducts through its leads and its tab, this one conducts through a single wide tab and a screw, which is a different thermal and mechanical problem rather than a different electrical one.

The ratings a buyer checks first

Drain to source voltage100 V
Gate to source voltageplus or minus 20 V
On resistance at 10 V gate, 30 A, 25 C3 milliohm
On resistance at 4.5 V gate, 60 A, 25 C4 milliohm
Continuous drain current, case at 25 C180 A
Continuous drain current, case at 70 C140 A
Pulsed drain current for 100 microseconds540 A
Single pulse avalanche energy and current1000 mJ from 0.5 mH, 110 A peak
Power dissipation, case at 25 C and 100 C300 W and 150 W
Junction to ambient on a one inch pad, junction to case40 and 0.5 C per watt
Gate threshold voltage at 250 microamp2.5 V minimum, 4.5 V maximum
Drain leakage at 100 V, 25 C, 125 C and 175 C1 microamp, 150 microamp and 5 mA maximum
Input, output and reverse transfer capacitance8200, 246 and 21 pF at 100 V
Total gate charge and gate drain charge105 and 16.9 nC typical
Turn on delay and rise time20 and 120 ns typical
Turn off delay and fall time38 and 80 ns typical
Body diode forward drop at 10 A0.8 V typical, 1.2 V maximum
Body diode reverse recovery40 ns typical

Reading the electrical table instead of the front page

The conduction arithmetic is the same as its TO-263 twin: 97 W at 180 A, 49 C of rise over the case at 0.5 C per watt, and about 31 A on a plain one inch pad before the ambient budget runs out. What the TO-247 adds is a thermal path that can actually remove that heat, because a 300 W dissipation figure with a case at 25 C assumes a heatsink with a fan or a chassis wall, and a bolted TO-247 is the cheapest way to reach it.

The switching rows differ from the seven lead version of the same die, and the difference is large enough to be a typing error rather than a real one: this sheet prints a 120 ns rise time where the TO-263 sheet prints 20 ns, both into a 1.66 ohm load at 100 V and 60 A, with the same gate charge and the same input capacitance. One of the two numbers is wrong, and a buyer who needs the edge rate should measure it rather than pick the sheet that suits the argument. The turn off delay of 38 ns against the other sheet's 30 ns is the same kind of drift.

The gate charge row carries the same contradiction as its twin: 105 nC in the typical column and 96 in the maximum column, which cannot both be true of one die. Sizing a driver on 105 nC plus tolerance is the only safe reading, and it means a 1 A peak driver turns the part on in roughly 150 ns at the gate, which is slower than the table's rise time and therefore sets the real edge.

The leakage rows are the ones that justify the 175 C junction claim, because they are specified at 175 C where a 150 C part would stop at 150 C. A drain leakage of 5 mA maximum at 175 C sounds large, and for a part switching 180 A it is irrelevant, but for a part used as a blocking switch in a battery product the 5 mA at the hot corner is 0.4 W of standing loss and has to be counted.

Where a 100 V TO-247 device earns its place

The first use is a 48 V to 12 V converter at several hundred watts, where the primary side switch dissipates 20 W to 30 W and a bracket bolted to the chassis removes it without a fan. The second is a battery disconnect or a precharge path on a 72 V pack, where the 540 A pulse covers the inrush and the 1000 mJ avalanche covers a cable inductance event.

The third is an inverter leg in a welding supply or a motor drive at 48 V to 60 V, where the switching frequency is low, the current is high and the body diode has to survive a commutation every cycle. The fourth is a class D amplifier at 60 V rail, where the 175 C junction gives room for a sustained musical load that a 150 C part would derate away from.

What the part is not is a hot swap element or a linear regulator pass device, for the same reason as every other 3 milliohm die: a linear event of 30 A at 80 V is outside any safe operating area this body can publish, and a hot swap function needs a device with an active limit.

Sourcing notes and the second source question

The useful thing about this part is that its seven lead sibling exists, so a buyer has two bodies for one die and can move between them without a new qualification of the switching behaviour. That is worth more than a nominal resistance difference, and our power management cross reference records which rows stay valid when only the body changes, which is everything except the thermal pair.

When the second source has to be a different vendor rather than a different body, the comparison has to include the avalanche rating and the recovery time, because two 100 V parts at 3 milliohm can differ by a factor of three on both. The how to verify a drop in replacement page sets out the bench sequence that settles those two rows.

On supply, a TO-247 is a through hole part and therefore less exposed to the surface mount allocation swings, but the die inside it is the same die as the surface mount versions, so a shortage at the die level hits both bodies at once. Our BOM shortage recovery page describes how we handle that case without a line stop.

Questions we answer before a reel is booked

The first is which rise time to believe. Two sheets for one die print 20 ns and 120 ns, so the honest answer is that the edge has to be measured on the board, and a converter budget should assume the slower figure with the driver actually used.

The second is the mounting. A TO-247 needs a thermal interface and a controlled mounting force, and the junction to case figure of 0.5 C per watt assumes a properly wetted interface. A dry joint or a warped tab can double that figure, which at 97 W is the difference between a 50 C and a 100 C rise.

The third is the gate drive. With a threshold window up to 4.5 V, only a 10 V drive reaches the published resistance with margin, and the 105 nC of gate charge at 100 kHz costs 10 mA of average driver current. A driver shared with small signal parts on the same rail should be checked against that number before the board is committed.