HXC50099
Product Specifications
HXC50099
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXC50099 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXC50099: 140 W, the rung between the singles and the pairs
The HXC50099 is a 140 W single ended LDMOS RF power transistor on a 50 V rail, filed on the HF to 1.0 GHz line and marked CW. It is the largest single ended row on this part of the shelf before the parts become pairs, and that position is what makes it worth a page of its own: it is the last rung where one device, one bias and one heat sink do the whole job.
140 W into 50 ohm is 51.46 dBm, 83.7 V rms and 118.3 V peak, which is 2.37 times the rail. The step up from the 100 W row is 1.46 dB and the step up to the 200 W row is 1.55 dB, so the shelf is built in roughly one and a half decibel steps and this row is squarely in the middle. A requirement of 120 W with 0.7 dB of margin lands here rather than on the 100 W row, and a requirement of 150 W does not.
No gain, no efficiency, no thermal resistance and no maximum ratings are published for this row, and the vendor page carries no parameter block in the copy read this round. What follows is the published row, the arithmetic that follows from it, and the measurement plan that replaces the missing figures.
The HXC50099 rows as the vendor publishes them
| Part class | LDMOS RF power transistor, unmatched, single ended |
| Frequency range, index row | HF to 1.0 GHz |
| Output, index row | 140 W |
| Output in dBm, calculated | 51.46 dBm |
| Step up from the 100 W row, calculated | 1.46 dB |
| Step up to the 200 W row, calculated | 1.55 dB |
| Step up to the 260 W pair, calculated | 2.69 dB, with a second device and a combiner |
| Drain rail, index row | 50 V |
| Mode, index row | CW |
| Load voltage at 140 W into 50 ohm, calculated | 83.7 V rms, 118.3 V peak |
| Peak against the 50 V rail, calculated | 2.37 times |
| Load voltage at a 2 to 1 mismatch, calculated | 237 V peak |
| Load voltage at a 3 to 1 mismatch, calculated | 355 V peak |
| DC input at 60 per cent efficiency, calculated | 233 W, 4.67 A at 50 V |
| Heat to remove at 60 per cent, calculated | 93 W |
| DC input at 55 per cent efficiency, calculated | 255 W, 5.09 A at 50 V |
| Heat to remove at 55 per cent, calculated | 115 W |
| DC input at 70 per cent efficiency, calculated | 200 W, 4.00 A at 50 V |
| Heat to remove at 70 per cent, calculated | 60 W |
| Gain | Not published |
| Efficiency | Not published |
| Thermal resistance, junction to case | Not published |
| Maximum ratings | Not published |
| Package | Not published on the row |
| Orderable addendum | None published |
| Moisture level and packing quantity | Not published |
The 2.37 ratio and the two ways to read it
At 140 W the peak load voltage is 2.37 times the rail, which is above the 2.00 of the 100 W row and below the 3.22 of the 260 W pair. Read as a single ended device, that ratio is high: a single ended stage at 2.37 times the rail is asking the drain to swing through more than twice the supply, and the breakdown voltage and the load line both have to allow for it. Read as a member of a family that also contains pairs, the number is unremarkable, because the pairs reach 3.2 to 4.0 on the same rail and are sold as normal products.
The practical consequence is in the output network. This row needs components rated above 355 V for the 3 to 1 mismatch case, which puts the network in the same part class as the 400 W pair rather than the 100 W single. A buyer who moves up from the 100 W row to this one should expect to change the output capacitors, not just the transistor, and the change is driven by the mismatch case rather than the matched case.
The second consequence is in the current. At 60 per cent efficiency the drain current is 4.67 A and at 55 per cent it is 5.09 A. That is still a single device current, so the bias network and the drain choke carry the same current as the 100 W row plus 40 per cent, which is within the same component family. This is why the row is the natural top of the single ended range: above it, the current and the voltage both cross into the territory where a pair is the simpler answer.
Thermal: 93 W to move and no published resistance
At 60 per cent efficiency the heat is 93 W, and at 55 per cent it is 115 W. Those numbers put the row beyond a small extruded sink and into forced air or a substantial natural convection sink. A 150 by 100 mm sink with 40 mm fins at a 40 degree rise can move about 90 W by natural convection, which is exactly at the limit and leaves no room for a hot day, so the honest recommendation at this power is a fan or a liquid cooled plate.
With no published thermal resistance the junction temperature cannot be computed from the vendor data. A planning assumption of 0.6 degrees per watt, which is between the 0.5 of the 260 W document and the 1.4 of the 60 W document on this shelf, gives 56 degrees of rise at 93 W and puts the junction at 141 degrees with an 85 degree case. That is a comfortable result on the assumption, and it is worth stating that the assumption is the weakest link in the chain rather than the part.
The measured route is better. Run the part at rated output into a dummy load for thirty minutes, read the flange temperature at the centre of the package and the ambient inside the enclosure, and compute the actual sink performance. Then ask the vendor for the thermal resistance and plug both numbers in. Two measurements and one email replace an estimate that could be 40 degrees wrong either way.
Drive and the gain question at 140 W
With nothing published, the planning range for this class is 14 to 18 dB, which puts the drive for 140 W between 2.2 W and 5.6 W. The upper end of that range is where a 5 W driver runs out of headroom, so a buyer planning a 140 W stage should budget for a 10 W driver and a pad rather than a 5 W driver and hope. The pad also buys stability into the unmatched input, which at this power is worth having.
Gain flatness across HF to 1 GHz is the second question. A single network cannot hold 140 W flat across a decade, so the practical use of this row is a sub band of 10 to 30 per cent bandwidth around a centre frequency, with the match cut for that band. The published range is an envelope, and the flatness inside the chosen sub band is a property of the network the buyer builds, not of the part.
The third question is linearity. The index says CW and says nothing about linear operation, and a 140 W CW rating does not translate into 140 W of average power with a modulated signal. For a linear application the average power has to be backed off by the peak to average ratio plus the linearity margin, which for a two tone test at minus 30 dBc intermodulation is typically 6 to 8 dB. That puts a 140 W part at 22 to 35 W of average power in a linear service, which is a very different number from the CW headline and is the one that belongs in the link budget.
Where the HXC50099 sits and when to jump to a pair
The ladder above this row continues with the 170 W and 200 W singles and then the pairs at 260, 400 and 500 W. Each single step is about 1.5 dB and each jump to a pair is about 3 dB plus the combiner loss, so a requirement above 200 W is normally met with a pair rather than with a larger single. The 260 W pair is 2.69 dB above this row and adds a second bias, a combiner and a reject load, which is the price of the next 3 dB.
The decision point is thermal rather than electrical. A single device at 93 W of heat needs one good interface and one sink; a pair at 173 W of heat needs two interfaces, a combiner that can take the power and a reject load sized on the amplitude error. Below about 150 W of heat the single is simpler, above it the pair is, and this row sits just under the line.
For the procurement view, this row is one where the absence of a published document makes the second source question urgent rather than optional. A buyer who needs 140 W and cannot get this part should know what else on the shelf is within half a decibel, and the answers, with the drive and heat at each rung, are on the RF power transistor cross reference page. The sourcing route for a part with no addendum, including how to get the packing quantity and the marking confirmed in writing, is on the RF component sourcing page. The inspection steps that catch a mislabelled or a reworked part before it reaches the line are on the incoming inspection plan page.
Questions buyers ask about the HXC50099
Why choose 140 W when 170 W and 200 W rows exist?
Because the steps are small and the thermal and component cost of each step is not. The 170 W row is 0.85 dB above this one and the 200 W row 1.55 dB above it, but both need bigger output capacitors and a larger sink for a modest gain. A requirement of 130 W takes this row at 93 per cent of rating; the 200 W row would run at 65 per cent of rating and cost more for 1.55 dB.
What driver does a 140 W stage need?
Plan on 14 to 18 dB of gain, which puts the drive between 2.2 W and 5.6 W. A 10 W driver with a 3 dB pad covers the whole range and leaves margin for the gain loss that comes with temperature and with a mismatched input. A 5 W driver covers the optimistic end only.
Can it run at 28 V instead of 50 V?
The index row is a 50 V part and no 28 V rating is published for it. Power scales roughly with the square of the rail, so a 28 V supply would give about 44 W at best, which is the territory of the 28 V rows on the same shelf that are specified for that rail. Running a 50 V part at 28 V is possible on a bench and is not a specification.