Contact Us

HXC50135

Brand: Hisiwell
Hisiwell HXC50135 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HXC50135 — Discrete & Power Semiconductors | Superb Automation

HXC50135

Hisiwell — Discrete & Power Semiconductors

Product Overview

The HXC50135 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

HXC50135: two power ratings on one row, and the band edge is the real specification

The HXC50135 is the clearest example on this shelf of a part whose headline number depends on which slice of the band is being used. The index row prints 750 W across 0.96 to 1.215 GHz on 50 V, with 14 dB of gain, 55 per cent efficiency and pulse mode. The vendor page prints two figures: 900 W over 1030 to 1090 MHz, and 750 W across the wider 960 to 1215 MHz band at reduced power. Both statements describe the same part, and the difference between them, 0.79 dB, is the cost of the band edge.

That is a normal way to publish a radar transistor. The 1030 to 1090 MHz window is where the interrogate and reply channels sit, and a part matched into that window can be pushed harder than the same part matched across 255 MHz. What is not normal is publishing the derating in prose and leaving the pulse conditions out entirely: there is no pulse width, no duty cycle and no thermal resistance on the page, and the data sheet link points at the site root.

For a buyer the two figures mean the amplifier has to be specified against the band it will actually cover. A 1090 MHz reply amplifier runs in the 900 W window; an amplifier that has to work from 960 to 1215 MHz takes the 750 W figure and gets 0.79 dB less output for the same drive, which is the same as losing 15 per cent of the drive power.

The HXC50135 rows as the vendor publishes them

Part classLDMOS RF power transistor, internally matched, single ended
Output, index row750 W
Output at 1030 to 1090 MHz, vendor page900 W
Output across 960 to 1215 MHz, vendor page750 W, described as reduced power
Output in dBm, calculated58.75 dBm at 750 W, 59.54 dBm at 900 W
Difference between the two ratings, calculated0.79 dB
Frequency range, index row0.96 to 1.215 GHz
Drain rail, index row50 V
Gain, index row14 dB
Drive for 750 W, calculated29.9 W, or 44.75 dBm
Drive for 900 W, calculated35.8 W
Drain efficiency, index row55 per cent
DC input at 750 W and 55 per cent, calculated1364 W, 27.3 A at 50 V
Heat to remove at that point, calculated614 W
Mode, index rowPulse
Application list, vendor pageIFF, secondary surveillance radar, ADS-B transponders, DME and other complex pulse chains
Pulse width and duty limitNot published
Thermal resistance, junction to caseNot published in text
Transient thermal impedanceNot published
Drain to source breakdownNot published in text
Input, output and feedback capacitanceNot published in text
Load mismatch toleranceNot published
Junction temperature maximumNot published in text
Package outlineNot published in text
Data sheet link on the vendor pagePoints at the site root, serves nothing
Parameters block on the vendor pagePublished as a picture, not as text
Orderable addendumNone published
Packing quantity and moisture levelNot published

IFF, secondary surveillance radar and DME are one band with three pulse formats

The application list on this page is unusually specific, and it is the most useful paragraph the vendor publishes. IFF and secondary surveillance radar share the 1030 MHz interrogate and 1090 MHz reply pair. ADS-B transponders transmit the 1090 MHz extended squitter. DME uses pulse pairs in the same region. All four are pulse systems with duty cycles well under a few per cent, and all four put the same demand on the transistor: peak power first, gain second, and average heat a distant third.

That is why a 750 to 900 W part exists in this band at all. The peak is what sets the link budget, and the duty is low enough that the heat sink can be sized on average power. A buyer coming from a continuous wave background will size the heat sink on the peak figure and end up with a flange three times larger than needed, and a buyer who sizes it on one per cent duty without checking the vendor's duty limit will run a pulse chain at ten per cent and wonder why the junction temperature climbs.

The pulse formats also decide the matching. A 0.5 microsecond pulse and a 12 microsecond DME pulse pair see the same impedance, but the bias loop has to recover between pulses, and a bias network with a slow settling time will droop on the first pulse of a burst. That is a board level issue, not a transistor one, and it is the reason a 900 W part that measures well on a single pulse can still fail a burst test.

Voltages at the connector on a 750 W pulse

750 W into 50 ohm is 193.6 V rms and 273.9 V peak. Against a 50 V rail that peak is 5.48 times the supply at the connector, and at 900 W it is 300 V. Those voltages are what the output network has to hold, and on a pulse part the peak matters more than the average because the breakdown of a capacitor is a peak event.

At a 2 to 1 load the peak reaches 548 V and at 3 to 1 it reaches 822 V. A 500 V rated capacitor on the output of this part is inside its rating on a perfect load and outside it on a 2 to 1 load, which is a failure mode that appears only during antenna sweeping or a connector fault. Choose the output passives against the mismatch case, and put a circulator after the device if the antenna can be disconnected while the transmitter is live.

The rail itself is modest at 27.3 A average at 750 W and 55 per cent. On a pulse chain the average current is far lower, so the supply is sized by the pulse current and the bulk capacitance, not by the average. That calculation needs the duty cycle the vendor has not published.

Thermal: 614 W of heat and no thermal resistance

At 750 W and 55 per cent the part produces 614 W of heat. With no junction to case figure in text, the flange budget has to be derived from a target: if the flange runs at 70 degrees and the junction limit is 225 degrees, the allowance is 155 degrees, which at 614 W is 0.25 degrees per watt. That is a copper and water territory figure, not an extruded heat sink figure.

On a pulse chain the average heat is what the flange sees, so the same 614 W becomes 61 W at 10 per cent duty and 6 W at 1 per cent. The DC thermal resistance is then the wrong tool, and the transient impedance for the actual pulse width is the right one. Neither is published, so the first prototype has to be instrumented rather than calculated: a thermocouple on the flange, a current probe on the drain and a known duty cycle will settle in an hour what the page cannot settle at all.

What the page does settle is the ordering of the risk. The transistor is the part with the published peak, and the heat sink, the output capacitors and the bias loop are the parts with the unpublished behaviour. On a 750 W pulse amplifier the second group is where the schedule goes.

Where the HXC50135 sits on the shelf

In the 960 to 1215 MHz group the rows run 90 W, 250 W, 300 W, 750 W, 900 W narrowband and 1000 W. This row is the 750 W one, and the vendor page adds a 900 W window in the middle of the band. From 750 W to 1000 W is 1.25 dB and from 300 W to 750 W is 3.98 dB, so the ladder jumps by about 4 dB below this row and by about 1.25 dB above it.

Read as a choice, this row is for a pulse system in the 1030 to 1090 MHz window that wants 900 W and can accept 750 W at the band edges, with 30 to 36 W of drive. A system that needs 1000 W at the top of the band takes the 1000 W row and pays for it in drive; a system that needs 300 W takes the 300 W row and gets 17 dB of gain instead of 14 dB.

Before the purchase order goes out

Three procurement points follow. No orderable addendum is published for this row, so the tray quantity, the moisture level and the marking have to come from the vendor in writing before a production order is placed, and the incoming route for a part whose two power ratings are published in prose is set out on the incoming inspection plan page. Buyers comparing this row against a competitor's 900 W L band pulse part should work from the RF power transistor cross reference, which lines the two up on band, duty and package rather than on the peak wattage. A bill of materials that carries the driver, the circulator and the high voltage output passives can be placed through the one stop RF supply route.