VBGL7103
Product Specifications
VBGL7103
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBGL7103 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBGL7103: a 180 A 100 V switch in the seven lead TO-263
The VBGL7103 is an N channel trench MOSFET in the seven lead TO-263 outline, printed at 100 V with plus or minus 20 V on the gate and a 175 C junction. On resistance is 3 milliohm at a 10 V gate with 30 A flowing and 5 milliohm at 4.5 V with 60 A, continuous drain current is 180 A with the case at 25 C and 140 A with the case at 70 C, and the pulsed rating is 540 A for 100 microseconds. Gate charge is 105 nC typical against 8200 pF of input capacitance, single pulse avalanche energy is 1000 mJ at 110 A peak, and the body diode recovers in 40 ns typical.
This part and the VBGP1103 in the TO-247 body carry the same electrical rows from the same die, which makes the pair useful for a product that starts on a heatsink bracket and moves to a surface mount assembly, or the other way round. The difference between the two is the thermal path and the mounting, not the silicon.
The ratings a buyer checks first
| Drain to source voltage | 100 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at 10 V gate, 30 A, 25 C | 3 milliohm |
| On resistance at 4.5 V gate, 60 A, 25 C | 5 milliohm |
| Continuous drain current, case at 25 C | 180 A |
| Continuous drain current, case at 70 C | 140 A |
| Pulsed drain current for 100 microseconds | 540 A |
| Single pulse avalanche energy and current | 1000 mJ from 0.5 mH, 110 A peak |
| Power dissipation, case at 25 C and 100 C | 300 W and 150 W |
| Junction to ambient on a one inch pad, junction to case | 40 and 0.5 C per watt |
| Gate threshold voltage at 250 microamp | 2.5 V minimum, 4.5 V maximum |
| Drain leakage at 100 V, 25 C, 125 C and 175 C | 1 microamp, 150 microamp and 5 mA maximum |
| Input, output and reverse transfer capacitance | 8200, 246 and 21 pF at 100 V |
| Total gate charge and gate drain charge | 105 and 16.9 nC typical |
| Turn on delay and rise time | 20 and 20 ns typical |
| Turn off delay and fall time | 30 and 80 ns typical |
| Body diode forward drop at 10 A | 0.8 V typical, 1.2 V maximum |
| Body diode reverse recovery | 40 ns typical |
Reading the electrical table instead of the front page
At 180 A the conduction loss is 97 W, which is the number that explains the rest of the sheet. Against 0.5 C per watt junction to case the die sits 49 C above a case that has to be cooled hard, and against the 40 C per watt ambient row the same loss is more than double the allowed budget. On a plain one inch pad the honest continuous figure is about 31 A: 2.9 W of loss, 115 C of rise over a 60 C ambient, and a junction at 175 C. Every amp above that has to come from copper, airflow or a heatsink.
The three milliohm row is measured at 30 A, one sixth of the rating, so it describes a cold die. The sheet prints no 125 C or 175 C row at all, which is unusual for a part that is promoted on a 175 C junction: the one place the high temperature enters the data is the leakage table, where the drain current limit rises from 1 microamp at 25 C to 5 mA at 175 C. A buyer who needs the hot resistance should ask for the curve, and should expect roughly double the cold figure at 125 C for a trench die of this voltage class.
The gate charge row has a contradiction inside it. The summary prints 105 nC typical, the electrical table prints 105 in the typical column and 96 in the maximum column, and a maximum below the typical cannot describe one device. The only defensible reading is that the maximum was copied from a smaller die in the same family, and a driver should be sized on 105 nC with margin rather than on either number as a guarantee. The gate drain charge of 16.9 nC and the 20 ns rise time are consistent with a die of this size.
The switching times split in an informative way: a 20 ns turn on delay and a 20 ns rise, then a 30 ns turn off delay and an 80 ns fall. A fall time four times the rise time is typical of a large die with a high output capacitance, and it means the turn off loss is the one that dominates at any given frequency. At 50 kHz the pair adds about 3 W of switching loss to the 97 W of conduction at full current, so the part is a low frequency switch by nature.
Where a 100 V 180 A device earns its place
The first use is the low side switch in a 48 V to 12 V synchronous buck at high current, where 3 milliohm at 100 A is 30 W and the seven lead body spreads that loss across a copper area the size of a business card. The second is a battery disconnect on a 72 V pack, where 100 V covers the regenerative transient and the 540 A pulse covers the inrush of a capacitive load.
The third is a brushless motor drive at 48 V, where the switching frequency is 20 kHz and the body diode handles the freewheel current between commutations. The 40 ns recovery and 0.8 V forward drop are the rows that matter there, and the 1000 mJ avalanche figure covers the inductive spike when a phase is disconnected under load.
What the part is not is a 200 kHz converter switch, and it is not a load switch in a small enclosure. At 8200 pF of input capacitance and 105 nC of gate charge, the driver has to be a real gate driver rather than a logic pin, and the heat has to leave through the tab into a plane that can take 30 W.
Sourcing notes and the second source question
A buyer replacing this part has two directions to go: a different die in the same body, or the same die in a different body. The second option is the safer one, because the electrical rows stay identical while the thermal path changes, and a product that moves from a bracket mount to a surface mount assembly keeps its qualification evidence. The power management cross reference marks the rows that have to be rechecked when the body changes, which is the thermal pair and nothing else.
The first option needs the capacitance and the gate charge compared, not just the resistance, because a 2 milliohm candidate with 12000 pF of input capacitance can be slower in the application than this part. The how to verify a drop in replacement page lists the bench checks in the order they catch a mismatch.
On supply, a 100 V die at 3 milliohm is a commodity part in a competitive band, and the reel sizes and date codes from different distributors can differ by more than a year. Our date code management page describes how we keep the age of a stock reel visible on a build so that a mixed batch does not pass unnoticed.
Questions we answer before a reel is booked
The first question is the current on the real board. The ratings page gives 180 A with a 25 C case; the one inch pad gives about 31 A, and the truth for a given product is somewhere between depending on the copper. A buyer planning 80 A continuous should be ready to show a heatsink or a thick copper plane.
The second is the gate charge maximum. Because the printed maximum is below the typical, the safe assumption is 105 nC plus the tolerance a driver can absorb, and a plan that relies on a 96 nC ceiling is relying on a typing error.
The third is the junction temperature limit. This sheet is consistent at 175 C across the feature line, the absolute maximum table and the leakage rows, which is unusual in this catalogue and worth noting: the part can be planned at 175 C, with the thermal path sized accordingly, rather than being derated to a 150 C basis as several of its neighbours have to be.