VBA1420
Product Specifications
VBA1420
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBA1420 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBA1420: a 40 V N channel in an SOP8
The VBA1420 is a single N channel in an SOP8. It is rated at 40 V, carries 9.5 A, and prints 19 milliohm at a 4.5 V gate against 16 milliohm at 10 V. The threshold is 1.8 V and the gate window is plus or minus 20 V. The technology is trench.
The SOP8 is the package that sits between the tiny SOT23 parts and the DFN family. It has no exposed pad, so its thermal path is through the eight leads, which limits it to about 1 watt in still air. What it does have is a footprint that any assembly line can place and inspect, and a lead pitch that survives hand rework.
The 40 V rating covers a 24 V rail with 16 V of margin and a 12 V rail with plenty. For a load of 3 to 5 A it is a comfortable part. For the 9.5 A headline the leads, not the die, are the limit.
Key data for the VBA1420
| Configuration | Single N channel |
| Package | SOP8, surface mount, no exposed pad |
| VDS | 40 V |
| VGS | Plus or minus 20 V |
| Vth | 1.8 V |
| ID | 9.5 A at 25 C case |
| RDS(on) at 4.5 V | 19 milliohm |
| RDS(on) at 10 V | 16 milliohm |
| Technology | Trench |
| Thermal path | Through the eight leads, no bottom pad |
| Gate drive | 4.5 V usable, 10 V for the printed best figure |
| Body diode | Intrinsic, source to drain |
Lead frame thermal limits in an SOP8
An SOP8 with no exposed pad has a junction to ambient resistance of roughly 100 to 130 degrees per watt when the drain leads are connected to a copper pour. At 120 degrees per watt and a 40 C ambient, a 125 C junction allows about 700 milliwatt. At 19 milliohm that is 6 A on paper, but the leads themselves add resistance and the solder joints are the real limit.
The practical continuous current is 3 to 4 A on a normal board, and 5 A if all four drain leads and all four source leads are poured into copper. Above that the part runs hot and the failure is a cracked solder joint rather than a dead die.
The 9.5 A headline assumes a 25 C case, which means a heatsink touching the package. In an SOP8 that is not a realistic mounting, so read the number as a pulse rating.
The 2.5 V question and gate drive detail
The table starts at 4.5 V, and the threshold is 1.8 V. That combination says the part will turn on from a 3.3 V pin, but the on resistance at 3.3 V is not published. A part with a 1.8 V threshold typically reaches about 1.4 times its 4.5 V resistance at 3.3 V, so expect around 27 milliohm. Ask for the curve before a 3.3 V drive is fixed.
At 10 V the part is 16 milliohm, only 16 per cent better than at 4.5 V, so there is little to gain from a driver on this part. That is the useful thing about a 40 V trench device: the curve flattens early, and a 5 V drive is nearly as good as 10 V.
The gate window of 20 V allows a 12 V drive with margin, which matters if the gate is driven from a 12 V rail through a resistor in a simple circuit.
Where an SOP8 40 V N channel fits
A 24 V relay or solenoid driver, a low side switch in a 12 V automotive accessory, a fan driver on a 24 V rail, and the pass element of a simple linear current limiter are all in range. The SOP8 also suits a product where the assembly house wants a package that can be inspected visually.
For a part that carries a load in a product built for years, the power management cross reference page covers what is checked before a substitute is accepted on a board that is already qualified.
The sourcing side of this part is covered on the component lead time solutions. For a package that many factories still hold in stock, that page covers how a shortage is handled without a re-qualification.
Questions we get on this code
Can it be driven from a 3.3 V microcontroller pin directly? It will turn on, at an on resistance above the 4.5 V column. For a load under 2 A that is usually acceptable. For more, use a driver or a lower threshold part.
Is 9.5 A continuous? No. Plan on 3 to 4 A continuous and up to 5 A with heavy copper on all leads. The 9.5 A is a 25 C case figure.
Does the package need a heatsink? An SOP8 has no tab to heatsink. The copper pour on the drain leads is the heatsink, and its area sets the current.
What is the switching speed? With a 10 ohm gate resistor and a 5 V drive the part switches in tens of nanoseconds. The SOP8 lead inductance starts to matter above 200 kHz, where the ringing has to be damped.