Contact Us

VBA3316SA

Brand: VBsemi
VBsemi VBA3316SA is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBA3316SA — Discrete & Power Semiconductors | Superb Automation

VBA3316SA

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBA3316SA from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBA3316SA: two N channels with a Schottky diode in the same SOIC-8

VBA3316SA is a dual N channel enhancement mode MOSFET from VBsemi in a SOIC-8 body, with a Schottky diode integrated alongside the two channels. Each channel is rated 30 V and 8 A at 25 degrees, with 8 milliohms at 10 V of gate drive and 12 milliohms at 4.5 V. The Schottky is rated 30 V reverse and 3 A forward, and it is the reason to pick this string over a plain dual.

The intended applications printed on the front page are set top boxes and low current DC to DC converters. Both are cost sensitive, both need two switches and a catch diode, and both have very little board area. A dual MOSFET plus a Schottky in one SOIC-8 replaces three placements and a handful of traces.

Two lines in the feature list are worth quoting to a quality team: the part is 100 percent unclamped inductive switching tested, and 100 percent gate resistance tested. Neither is a performance claim. Both are statements about what every piece is screened for, and they are the sort of thing that shows up in an incoming inspection discussion.

What the integrated Schottky does

A synchronous buck uses the low side channel instead of a diode, and the body diode of that channel conducts during the dead time. A Schottky in parallel with the body diode conducts at a lower forward voltage, so the dead time loss falls and the reverse recovery charge that the high side switch has to swallow is smaller. In a converter running at a few hundred kilohertz with a small load, that difference is worth more than the extra part costs.

In a non synchronous converter the Schottky is the catch diode and the two channels are a switch and a load switch. That is the set top box arrangement, where the current is under 2 A and the switching frequency is modest.

Configurationtwo N channel MOSFETs with an integrated Schottky diode
Drain source rating30 V per channel
Gate source limitplus or minus 12 V
Continuous current8 A at 25 degrees, 6.8 A at 70 degrees
Pulsed current40 A
Power dissipation2 W at 25 degrees, 1.44 W at 70 degrees
On resistance at 10 V8 milliohms at 5 A
On resistance at 4.5 V12 milliohms at 4 A
Gate threshold1 V to 2.5 V at 250 microamps
Transconductance16 siemens at 10 V and 5 A
Total gate charge15 nC typical at 10 V and 5 A
Gate source charge3.7 nC typical
Gate drain charge1.05 nC typical
Input capacitance586 pF at 15 V and 1 MHz
Output capacitance117 pF
Reverse transfer capacitance55 pF
Gate resistance0.8 ohm typical
Turn on delay12 ns typical, 24 ns maximum
Body diode forward voltage0.8 V typical, 1.2 V maximum
Body diode reverse recovery11 ns typical, 4 nC typical charge
Schottky rating30 V reverse, 3 A forward continuous
Channel diode current2.25 A continuous source current
Junction rangeminus 55 to plus 150 degrees Celsius
PackageSOIC-8, eight pins
Constructiontrench, halogen free, RoHS compliant

Loss arithmetic for the set top box case

At 5 A and 8 milliohms a channel dissipates 0.2 W. At 4 A through the 12 milliohm figure at 4.5 V drive it is 0.19 W. The package is rated 2 W at 25 degrees, so a single channel at 5 A uses a tenth of the rating and the part runs cool. That headroom is why the package is used for converters in the 2 to 4 A class rather than the 8 A the headline allows.

The Schottky is the part that gets warm in a non synchronous converter with a high duty cycle. At 1 A forward and 0.5 V it dissipates half a watt, and while the diode is rated 3 A the practical continuous figure in a SOIC-8 is set by the thermal path through the leadframe. A board that runs the diode at 2 A continuously should measure the case temperature rather than assume the rating applies.

Gate drive and the 12 V limit

The gate source limit is plus or minus 12 V, so a 10 V drive is the normal choice and the on resistance figures are printed at 10 V and 4.5 V. A 12 V rail used directly on the gate leaves no margin for ringing and is outside good practice even though it is inside the absolute limit.

The gate resistance of 0.8 ohm typical is low, and the gate charge of 15 nC is small, so the part switches quickly with a modest driver. With 586 pF of input capacitance the turn on is in the tens of nanoseconds, and the gate loop arrangement is what decides whether that edge rings. The 12 V limit makes the loop more important, not less.

The diode, the body diode and reverse recovery

A Schottky in parallel with a body diode shares current according to the forward voltage curves, and the crossover is at a current that depends on temperature. At low current the Schottky takes most of it; at high current the body diode takes a share. That is why the specification prints both diodes rather than only the Schottky.

The reverse recovery charge of 4 nC typical for the body diode is small enough that the high side switch sees a modest spike. In a converter with a 30 V rail and a fast high side, that is the difference between a 5 V overshoot and a 15 V overshoot, and it is the reason a Schottky is added to a synchronous stage in the first place.

Where this part fits and where it does not

It fits a set top box, a small DC to DC module, a relay driver with a catch diode, and any board that needs two switches and a freewheel diode in a small area. It does not fit a converter above about 4 A per channel, and it does not fit a 48 V rail where the 30 V rating is not enough.

For a build that needs the part plus the inductor and the capacitors as one kit, the one stop BOM sourcing route keeps the power stage together. The power management cross reference page covers the comparison against a plain dual MOSFET plus an external Schottky, which is the arrangement this part replaces.

Substitution checks

A substitute has to match four things: the pinout including the diode pins, the on resistance at the real gate drive, the gate charge at the real frequency, and the diode rating. A part that matches the first three and has a 1 A diode will fail in a converter that relies on a 3 A diode, and the failure appears as a diode that runs at 150 degrees rather than as a part that does not work.

The pin to pin cross reference page sets out the sequence, and for this part the diode pinout is the first thing to check because a dual MOSFET without the diode has a different internal connection on two pins.

Three questions buyers ask about this string

Is the Schottky per channel or shared? It is a separate diode in the same package, connected across one channel in the arrangement printed in the pin table. A board that needs a diode on both channels needs two parts or an external diode.

Can it replace a dual MOSFET plus an external Schottky? Electrically yes at 5 A and 30 V, and the board has to be reworked for the internal connection. The saving is one placement and the trace between them.

Is the 8 A rating usable? At 25 degrees on a board with copper, a single channel at 8 A is 0.5 W and runs warm but within the package rating. In a closed box, 4 A per channel is the honest continuous figure.