VBE1606
Product Specifications
VBE1606
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBE1606 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBE1606: a 60 V, 5 milliohm N channel rated to 175 C
The VBE1606 is a single N channel MOSFET in the TO-252 body, printed at 60 V from drain to source with plus or minus 20 V on the gate, tested for gate resistance and unclamped inductive switching, in a package the vendor describes as low thermal resistance. On resistance is 0.0050 ohm at a 10 V gate with 25 A flowing and 0.0120 ohm at a 4.5 V gate with 20 A, and the same die measures 0.0117 ohm at 125 C and 0.0149 ohm at 175 C. Continuous current is 97 A with the case at 25 C and 56 A at 125 C, the source current is 100 A, the pulsed rating is 290 A, and the single pulse avalanche energy is 101 mJ into 0.1 mH. A 60 V, 5 milliohm die in TO-252 is a serious pass element, and the 175 C junction rating is what makes it usable in a sealed enclosure.
Thermal resistance is 1.1 C per watt junction to case and 50 C per watt junction to ambient, with 136 W of dissipation at a 25 C case and 45 W at 125 C. At 30 A the die loses 4.5 W at a 10 V gate and 10.8 W at 4.5 V, which is the difference between a part that runs at a 5 C case rise and one that needs a bigger tab. The sheet also carries a note that parametric verification is ongoing, which is printed by the vendor and is worth repeating here: the numbers on this page come from the vendor document, and the note applies to the document rather than to this page.
The ratings a buyer checks first
| Drain to source voltage | 60 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at 10 V gate, 25 A | 0.0050 ohm |
| On resistance at 4.5 V gate, 20 A | 0.0120 ohm |
| On resistance at 125 C and 175 C junction | 0.0117 ohm and 0.0149 ohm |
| Continuous drain current | 97 A at 25 C case, 56 A at 125 C case |
| Continuous source current, diode | 100 A |
| Pulsed drain current | 290 A |
| Single pulse avalanche | 45 A into 0.1 mH, 101 mJ |
| Power dissipation | 136 W at 25 C case, 45 W at 125 C case |
| Junction to ambient, junction to case | 50 and 1.1 C per watt |
| Gate threshold voltage | 2.0 V minimum, 4.0 V maximum |
| Total gate charge at 10 V gate | 82 nC typical, 125 nC maximum |
| Gate source and gate drain charge | 14.5 nC and 13.5 nC |
| Input and output capacitance | 4844 and 441 pF typical, 6060 and 555 maximum |
| Junction and storage range | minus 55 to plus 175 C |
Reading the electrical table instead of the front page
The threshold window is 2.0 V to 4.0 V at 250 microamp, so a 4.5 V drive leaves only 0.5 V of overdrive on the worst case die and the 0.0120 ohm row is a typical rather than a guarantee. This is a 10 V gate part. A product with a 5 V rail has to either accept a resistance two and a half times the headline or add a small charge pump, and the pump is usually cheaper than the extra copper. The resistance over temperature is the other row to read: 5 milliohm at 25 C becomes 11.7 at 125 C and 14.9 at 175 C, a factor of three, so a loss budget written at room temperature is wrong by that factor in the product.
Gate charge is 82 nC typical and 125 nC maximum at a 10 V drive, with 14.5 nC of gate source charge and 13.5 nC of gate drain charge, and the input capacitance is 4844 pF typical and 6060 pF maximum. At 100 kHz the driver moves 8.2 mA and at 300 kHz it moves 25 mA, which is a driver with a real output stage rather than a logic pin. The switching times are 14 ns turn on delay and 5 ns rise, 41 ns turn off delay and 7 ns fall at 50 A with a 1 ohm gate resistor, so the edges are fast and the gate loop has to be short. A 13.5 nC gate drain charge with a 5 ns rise means the part belongs in hard switching at a moderate frequency, not for a resonant tank.
The body diode is 100 A continuous with the forward voltage quoted at 50 A, and the sheet does not print a recovery time for this body, which is a gap worth naming rather than filling from a distributor page. For a synchronous application the missing recovery figure is the one that would decide whether a parallel Schottky is needed, so a customer using this part in a bridge should either measure the recovery on a sample or keep the diode conduction time short enough that the charge does not matter.
Where a 60 V, 5 milliohm switch with a 175 C junction earns its place
The first case is a 48 V to 12 V synchronous buck at 20 A to 40 A, where 60 V covers the input rail with a 25 per cent margin and 5 milliohm keeps the conduction loss under a watt at low duty. The 175 C junction allows the part to sit in a sealed box without derating the current to half, and 45 W of dissipation at a 125 C case is a figure that a TO-252 on a heat spreader can reach. The second case is a 48 V battery or telecom rail used as a pass element, where 97 A at a 25 C case is the burst rating and 56 A at 125 C is the one to size to.
The third case is a motor drive low side on a 36 V or 48 V rail, where the 290 A pulsed rating covers the stall current for a few hundred microseconds and the 101 mJ avalanche rating covers the back EMF the clamp does not. In all three the part is chosen because the junction rating and the resistance allow the same footprint to carry twice the current of a 12 milliohm part, and the price is paid in gate charge and in a threshold that wants a 10 V driver.
Sourcing notes and the second source question
A 5 milliohm 60 V part is a die where the headline resistance is easy to match and the temperature coefficient is not, so two parts that both read 5 milliohm at 25 C can be 11.7 and 15 milliohm at 125 C. Our power management cross reference keeps the hot resistance row and the gate charge beside the 25 C figure, so a replacement is compared at the temperature the product runs at. Where a customer needs a part that will not be trimmed from the portfolio, the route in last time buy and LTB planning keeps a date code window and a stock reservation rather than a substitute with a different threshold.
For a part going into a qualified supply, how to verify a drop in replacement sets out the tests: gate ringing at the new charge, efficiency at the real switching frequency, junction temperature at the case the enclosure produces and diode behaviour in the dead time. The impedance of the gate loop is part of the test, because a 5 ns rise time will find a 20 mm gate trace and turn it into a radiator.
Questions we answer before a reel is booked
The first question is whether the 97 A rating is usable. It is a case temperature figure with a heat spreader; in still air the 50 C per watt path makes the part a 2.5 A device at a 125 C rise, so the rating describes the package, not the board. The second question is whether the 4.5 V row applies to a 5 V gate drive. It does not on a worst case die, because the maximum threshold is 4.0 V, so a 5 V rail leaves 1 V of overdrive at best.
The third question is about the missing recovery time. The sheet prints the diode current and the forward voltage at 50 A but no reverse recovery row, so a bridge built on this part should measure the recovery on a sample or keep the diode conduction short. The fourth is about avalanche. The 101 mJ single pulse into 0.1 mH covers a modest leakage inductance, and the 175 C junction means the derating for repeated events is less severe than on a 150 C part, but a clamp is still cheaper than a field return.
On supply, the reel is quoted with the date code on the label and the moisture level from the packing list, the reflow window is a 260 C peak, and incoming inspection samples the on resistance at 10 V and 4.5 V, the hot resistance at 125 C and the threshold at 250 microamp. The vendor note that parametric verification is ongoing is recorded here rather than smoothed over, and a customer who needs a guaranteed hot resistance should ask for the vendor confirmation against the lot.