Contact Us

VBC6N3010

Brand: VBsemi
VBsemi VBC6N3010 is a discrete semiconductors component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBC6N3010 — Discrete & Power Semiconductors | Superb Automation

VBC6N3010

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBC6N3010 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBC6N3010: two N channels with the drains tied together

The VBC6N3010 is a common drain pair in a TSSOP8. Two N channels share one drain node, so the two sources point in opposite directions and the pair blocks current in both directions when both gates are off. The part is rated at 30 V, carries 8.6 A, and prints 19 milliohm at a 4.5 V gate against 12 milliohm at 10 V. The threshold is 1.7 V and the gate window is plus or minus 20 V.

The common drain connection is the reason this part exists. A single N channel always has a body diode from source to drain, so it can block in one direction only. Two N channels with their drains joined have two body diodes facing each other, and the series combination blocks in both directions until both gates are driven. That is the arrangement a battery protection switch needs, and it is also the arrangement a bidirectional load switch or an ideal diode OR-ing pair needs.

Because both halves sit on one die, the two on resistances track each other with temperature. A discrete pair built from two separate parts does not, and the mismatch shows up as asymmetric loss in a path that is supposed to be symmetric.

Key data for the VBC6N3010

ConfigurationDual N channel, common drain
PackageTSSOP8, surface mount
VDS30 V
VGSPlus or minus 20 V
Vth1.7 V
ID8.6 A
RDS(on) at 4.5 V19 milliohm
RDS(on) at 10 V12 milliohm
TechnologyTrench
Blocking directionBoth, while both gates are held low
Body diodesTwo, in series opposition through the shared drain
IsolationNone, both sources sit at different potentials and the gates need separate drive

Two gates, two drive levels, one shared node

In a common drain pair the two sources are the two terminals of the switch, and each gate has to be driven relative to its own source. When the switch is closed, both sources sit within a few tens of millivolts of each other, so one gate driver referenced to either terminal will work for both. When the switch opens, the two sources separate by the full blocking voltage, and a driver referenced to one terminal now overdrives or underdrives the other gate.

This is why protection circuits built around a common drain pair normally use a dedicated protection IC with two gate outputs, or a charge pump referenced to the mid point. Driving both gates from one pin works only while the switch is closed, which is exactly when it does not matter.

The 30 V rating sets the maximum standoff in the open state. A 24 V system that can ring to 35 V on a load dump will exceed it, and the pair fails short rather than open. For a 12 V or a 24 V nominal rail with clamped transients the rating is adequate. For anything derived from an alternator without a clamp, it is not.

Conduction loss in a two device path

Two devices in series means two on resistances in the path, so the pair behaves like 38 milliohm at a 4.5 V gate rather than 19. At 5 A that is 950 milliwatt spread across the die, and the TSSOP8 lead frame has to carry it out. At 8.6 A it is 2.8 watt, which no TSSOP8 will hold without a copper pour under the leads and airflow over the board.

The 12 milliohm figure at a 10 V gate is the one to use when the drive can reach 10 V, because the pair halves the loss. On a 12 V rail a gate driver with a 10 V output is available, and it is the cheapest way to recover the margin. On a 3.3 V rail the drive will sit at 2.5 V to 3 V, well below the published 4.5 V column, so the real on resistance has to come from the full data sheet curve.

Where a common drain pair is the right answer

The first application is a one cell or two cell battery pack where the protection switch has to block charging current and discharging current from the same two terminals. The second is a load switch on a rail that may be back fed from an external adapter, where a single N channel would conduct through its body diode and never isolate. The third is an ideal diode pair in an OR-ing circuit where the two inputs can be at different potentials.

For a switch that decides whether a rail is alive, the part is usually bought against a programme that lasts years rather than against a single order, and the power management cross reference page covers how a substitute is checked when the original code is short.

The sourcing side of this part is covered on the incoming inspection plan. For a switch that sits in the battery path, that page covers what is checked at the receiving dock before a reel enters a line.

Questions we get on this code

Can I use one of the two channels on its own? Yes, but only as a high side switch with its body diode in the direction the load needs. The other channel has to have its gate tied to its source, never left floating.

How much standoff do I get in the open state? The full 30 V, split across the two devices according to their off state leakage. Two devices of the same die share it evenly, so the pair gives 30 V total, not 60 V.

Does the part work as a reverse polarity protection? It does, with the gate driven from the protected rail. The catch is that the gate drive has to come up before the load draws current, otherwise the pair conducts through the body diodes and drops about 1.4 V.

What is the switching behaviour when both gates are driven together? The two devices turn on within a few nanoseconds of each other if the drive is symmetric. Any difference in gate resistance shows up as a short interval in which one device carries the whole current, which is why the two gate resistors should be matched.