VBM2603
Product Specifications
VBM2603
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBM2603 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBM2603: a 60 V P channel at 120 A in a TO220
The VBM2603 is a single P channel MOSFET rated at minus 60 V drain to source with a plus or minus 20 V gate window and a threshold of minus 3.5 V. It carries minus 120 A and its on resistance is 3 milliohm at a 10 V gate. The die is trench silicon and the body is the TO220 through hole package.
Three milliohm on a P channel is rare, because a P channel needs roughly twice the area of an N channel for the same resistance. Getting to 3 milliohm in a TO220 means the die fills the tab, and it means the gate charge is large. The 120 A figure belongs to the same die at a 25 C case.
The application is a battery disconnect on the high side, a reverse polarity block that has to carry the whole load, or a high current load switch where the gate cannot be driven above the rail. All three are cases where an N channel with a charge pump would be cheaper in silicon and more expensive in circuit.
Key data for the VBM2603
| Configuration | Single P channel |
| Package | TO220, three lead through hole with tab |
| VDS | Minus 60 V |
| VGS | Plus or minus 20 V |
| Vth | Minus 3.5 V typical |
| ID | Minus 120 A, a die limit at a 25 C case |
| RDS(on) at 10 V | 3 milliohm |
| Technology | Trench |
| Gate charge | Not published on the catalogue page, and on a die this size it is the switching budget |
| Body diode | Intrinsic, cathode at drain, which is the direction a battery block needs |
| Gate drive | The gate has to be pulled 10 V below the source, so a driver or a charge pump is needed on a 24 V rail |
| Thermal path | Tab to heatsink, with an insulating pad when the sink is earthed |
Driving a P channel gate 10 V below a rail
A minus 3.5 V threshold is high for a P channel, and that is deliberate. A high threshold means the part does not creep on when the gate is only a volt or two below the source, which matters on a high current switch where a partially on device dissipates far more than an off one. The price is that the gate has to be pulled 10 V below the source to reach the 3 milliohm figure, and 10 V below a 48 V rail is 38 V, which is outside the 20 V gate window.
So the gate drive cannot be a simple pull to ground. It has to be a level shifted driver, a charge pump referenced to the source, or a resistor divider with a clamp that holds the gate source voltage inside 20 V while still providing 10 V of overdrive. Each of those is a small circuit, and on a high current switch the circuit is worth the effort because the alternative is running the part at a resistance three times higher.
The threshold also sets the turn off behaviour. When the driver releases the gate, the source to gate capacitance discharges through whatever resistor is there, and if that resistor is too large the part stays partly on during a fault and absorbs the fault energy. A defined turn off path is part of the specification, not an optional extra.
120 A in a TO220, and what that really means
At 30 A the part dissipates 2.7 watt and the tab on a modest heatsink runs 40 degrees above ambient. At 60 A it is 10.8 watt and the sink has to be real. At 120 A it is 43 watt, which a TO220 can shed only with a large sink and forced air, so the headline is a die and bond wire limit rather than a working point.
The die is large, which means two things beyond the current. The gate charge is large, so switching is slow unless the driver is strong. And the thermal cycling between the die and the tab is more severe, so the number of power cycles before a solder fatigue failure is lower than on a small die. For a battery disconnect that switches once per charge cycle, the count is small and irrelevant. For a load switch that cycles every second, it is not.
The body diode in a reverse polarity block carries the inrush current when the pack is connected the wrong way, which is a single event at a few hundred amps for a few hundred microseconds. The diode survives that because the die is large, and it is one of the reasons a pair of P channels at 3 milliohm is chosen over a smaller part with a fuse.
Stock and excess on a high current P channel
Parts in this cell are bought in large quantities by a small number of programmes, so the market alternates between scarcity and excess. Our supplier scorecard page covers how a source is scored across a programme, which is what makes it possible to say whether a sudden offer of stock is credible.
For a part at this current level the date code and the storage history matter more than usual, because a large die with a large tab is the shape that suffers from moisture uptake and from thermal cycling in storage. A reel or a tube of parts that has been through two summers in a warehouse is not the same as a fresh one, and the quotation should say which it is.
The sourcing side of this part is covered on the excess inventory management. For a large die P channel bought in programme quantities, that page covers how excess is identified and how age is handled.
Questions we get on this code
Can the gate be pulled to ground on a 48 V rail? No. That is 48 V below the source and outside the 20 V window. A level shifted driver or a clamp is required.
Is 120 A continuous? No. With a heatsink the working current is 30 to 60 A, and the 120 A figure is a die limit at a 25 C case.
What is the on resistance at a 4.5 V gate? Not published on the catalogue page. The 3 milliohm figure is a 10 V number, and a part with a minus 3.5 V threshold driven at 4.5 V is only 1 V into conduction.
How is it packed? TO220 normally ships in tubes. We confirm the tube count, the date code and the storage record on the quotation.