VBE1101N
Product Specifications
VBE1101N
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBE1101N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBE1101N: a 100 V N channel at 8.5 milliohm in TO-252
The VBE1101N is a single N channel MOSFET in the TO-252 body, printed at 100 V from drain to source with plus or minus 20 V on the gate, tested for gate resistance and for unclamped inductive switching on every unit. On resistance is 0.0085 ohm at a 10 V gate with 30 A flowing and 0.0105 ohm at a 4.5 V gate with 20 A, and the same die measures 0.017 ohm at a 125 C junction and 0.022 ohm at 175 C at the 10 V drive. Continuous current is 85 A with the case at 25 C and 75 A at 125 C, package limited, with a 300 A pulsed rating and a 280 mJ single pulse avalanche energy. The vendor files the part under primary side switch and isolated converter, which is where a 100 V, 8.5 milliohm die at 85 A belongs.
The thermal numbers are what make the current rating credible. Junction to case is 0.85 C per watt typical and 1.1 maximum, so 210 W can cross the tab with the case at 25 C, and junction to ambient is 40 C per watt on an FR4 pad, so the same part in still air is a 3.25 W device. That gap of two orders of magnitude is not a quirk of this sheet; it is the whole reason a TO-252 part is quoted at 85 A and used at 15 A on a board without a heat spreader. A buyer who plans a 30 A continuous load has to plan the copper and the airflow, not just the reel.
The ratings a buyer checks first
| Drain to source voltage | 100 V |
| Gate to source voltage | plus or minus 20 V |
| On resistance at 10 V gate, 30 A | 0.0085 ohm |
| On resistance at 4.5 V gate, 20 A | 0.0105 ohm |
| On resistance at 125 C and 175 C junction | 0.017 ohm and 0.022 ohm |
| Continuous drain current | 85 A at 25 C case, 75 A at 125 C case, package limited |
| Pulsed drain current | 300 A |
| Single pulse avalanche | 75 A into 0.1 mH, 280 mJ |
| Power dissipation | 210 W at 25 C case, 3.25 W at 25 C ambient |
| Junction to ambient, junction to case | 40 and 0.85 C per watt typical, 50 and 1.1 maximum |
| Gate threshold voltage | 1 V minimum, 4 V maximum |
| Total gate charge at 10 V gate | 105 nC typical, 160 nC maximum |
| Gate source and gate drain charge | 17 nC and 23 nC |
| Input, output and reverse transfer capacitance | 4000, 565 and 205 pF |
| Body diode forward voltage at 85 A | 1.0 V typical, 1.5 V maximum |
| Junction and storage range | minus 55 to plus 175 C |
Reading the electrical table instead of the front page
The threshold window is the widest on any part in this band: 1 V minimum and 4 V maximum at 250 microamp. A 4.5 V gate drive therefore has only 0.5 V of overdrive on the worst case die, which is why the 4.5 V resistance row is 24 per cent above the 10 V row and why a board that runs at 5 V should either accept that resistance or add a small charge pump. The zero gate drain current tells the same story about the die size: 1 microamp at 25 C, 50 microamp at 125 C and 250 microamp at 175 C, which is leakage from a large area and not a failure mode.
Gate charge is the price of the low resistance. At 105 nC typical and 160 nC maximum on a 10 V drive, with 23 nC of gate drain charge, the driver has to move real current: at 100 kHz that is 10.5 mA of average gate current and 105 mW in the driver, and at 300 kHz it is 32 mA and 315 mW. A gate resistor chosen for a 20 nC part will be far too large here, and the switching times show what the charge buys: 12 ns turn on delay and 90 ns rise at 85 A, 55 ns turn off delay and 130 ns fall, all with a 2.5 ohm gate resistor. Those are fast edges at 85 A and they will ring without a proper gate loop, so the resistor and the return path are electrical components, not decoration.
The body diode is substantial: 1.0 V typical and 1.5 V maximum at 85 A, 85 A continuous, 140 A pulsed, 85 ns recovery and 0.17 microcoulomb of recovered charge. On a synchronous stage the diode carries current during the dead time and the recovery charge is lost every cycle, so at 150 kHz a 0.35 microcoulomb maximum is 52 mA of equivalent loss current. The avalanche rating of 280 mJ is the largest in this band and is what makes the part usable as a primary side switch, where the leakage inductance of the transformer is dumped into the drain node on every turn off.
Where a 100 V, 8.5 milliohm switch earns its place
The first case is the primary side of an isolated converter running from a 48 V rail. A 100 V part leaves 52 V of margin for the leakage spike that a flyback or a forward converter produces, and the 280 mJ avalanche rating covers the energy that the clamp does not, which is what keeps a 48 V to 12 V module alive when the load steps. At 20 A the die loses 3.4 W, which needs the tab soldered to a copper area of a few square centimetres to stay under a 125 C junction in a 60 C enclosure.
The second case is a 72 V or 80 V battery path, where the 100 V rating is the minimum that a fully charged string and a charger overshoot will tolerate, and the low resistance matters because the forward drop is the whole loss. The third case is a hot swap or an OR-ing stage on a 48 V backplane, where the 300 A pulsed rating and the 85 A continuous figure cover a card insertion event and the 0.85 C per watt junction to case lets the tab sit on the backplane copper. In all three, the driver has to be able to source and sink the 160 nC maximum charge at the switching frequency, and that is the check people forget.
Sourcing notes and the second source question
A 100 V TO-252 switch at 8.5 milliohm is a part where two vendors can print the same resistance at different test currents, one at 30 A and one at 60 A, and the second number hides a larger temperature coefficient. Our power management cross reference keeps the test current, the 125 C row and the gate charge in the same line as the headline resistance, so a replacement is compared on the conditions it will actually run at. When a customer sends a competitor code, the rows we read first are the resistance at 125 C, the threshold maximum, the gate charge maximum and the avalanche energy.
For a part that has to be proven on an existing board, how to verify a drop in replacement lists the tests in the order that finds problems fastest on a primary side switch: gate ringing at the new charge, the leakage spike against the clamp, the diode recovery in the secondary and the junction temperature on the real tab area. Where the original body is being trimmed from a portfolio, the route in last time buy and LTB planning is the one that keeps a line running with a date code window and a stock reservation rather than a substitute that needs a new footprint.
Questions we answer before a reel is booked
The first question is whether 85 A can be carried. It can with the case held at 25 C and a heat spreader on the tab, and it cannot on an FR4 pad in still air, where the same part is a 3.25 W device and 20 A already means 3.4 W. The second question is whether the 4.5 V row is usable. It is, at 0.0105 ohm, but only with a driver that puts 4.5 V on the gate at the die and not at the pin, because the 1 V minimum threshold leaves too little overdrive for a resistor drop in the gate path.
The third question is about avalanche energy. The 280 mJ single pulse rating is a one shot figure into 0.1 mH and repeated events derate with junction temperature; a converter that clamps the spike properly uses a small fraction of it, and a converter that relies on it will fail in the field. The fourth is about the diode. The 85 A continuous diode current and the 0.17 microcoulomb recovery charge mean the part can carry the freewheel current, but the 1.5 V maximum forward drop at 85 A is 128 W of dissipation, which no TO-252 can shed, so the diode is a transient path and not a steady one.
On supply, the reel is quoted with the date code on the label and the moisture level from the packing list, the reflow window is a 260 C peak, and incoming inspection samples the on resistance at 10 V and 4.5 V, the threshold at 250 microamp and the avalanche sample record. This family publishes no orderable addendum, so no reel size or marking code is quoted here, and a customer who needs a specific date code window for an already qualified product has to book it before the order is placed.