HXC50167
Product Specifications
HXC50167
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXC50167 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXC50167: a 70 W push pull pair on 28 V whose document carries a different name
The HXC50167 is a 70 W LDMOS pair on the HXC50 shelf: 35 W per side, two sides, a 28 V rail, 19 dB of gain and 60 per cent drain efficiency on the index row, marked CW. The product page adds the list that tells a buyer where the part is normally sold, ground communication from 30 to 88 MHz, TV VHF I at 54 to 88 MHz, FM broadcast at 88 to 108 MHz, avionics at 118 to 140 MHz, land mobile at 136 to 174 MHz, TV VHF III at 160 to 230 MHz, jammers at 30 to 512 MHz and TV UHF at 470 to 860 MHz. That list is the commercial description. The engineering description sits in the document attached to the page, and that document is titled HX215078, not HXC50167.
The naming gap is the first thing to settle before a purchase order goes out. The document describes a 70 W unmatched push pull LDMOS pair for wideband and mobile radio below 1500 MHz, which matches the catalogue row in power, rail, topology and band, so the two names very probably describe one die. No statement on the vendor site says so, and a goods inwards clerk comparing the label to the order will see two names and hold the shipment. The page states the gap in the table below rather than presenting the document as confirmed for the catalogue number.
The second thing to settle is which gain figure is real. The index row prints 19 dB. The document prints 20 dB at 1000 MHz in a soldered fixture with a 28 V rail and 500 mA of quiescent current. One decibel is the difference between 0.88 W and 0.70 W of drive at this power, which matters when a driver stage is being chosen at the edge of its range, so plan the driver on the 19 dB figure and treat 20 dB as an upside that has to be measured on your own board.
The HXC50167 rows as the vendor publishes them
| Part class | LDMOS RF power transistor, unmatched, push pull, two devices in one package |
| Output, index row | 35 W per side, 70 W for the pair |
| Output in dBm, calculated | 45.44 dBm per side, 48.45 dBm for the pair |
| Frequency range, index row | HF to 1.5 GHz |
| Frequency measured in the document | 1000 MHz, single point, on a fixture with the device soldered |
| Drain rail | 28 V nominal, 40 V maximum operating |
| Quiescent current in the functional test | 500 mA |
| Gain, index row | 19 dB |
| Gain, document at 1000 MHz | 20 dB typical |
| Output at 1 dB compression, document | 70 W typical |
| Drain efficiency at that point, document | 60 per cent typical |
| Input return loss, document | minus 10 dB typical |
| Drain to source breakdown, document | 95 V typical, 90 V minimum at 1 mA |
| Gate to source maximum, document | minus 10 V to plus 10 V |
| Junction temperature maximum, document | 225 degrees C |
| Case operating temperature, document | 150 degrees C |
| Storage temperature, document | minus 65 to plus 150 degrees C |
| Thermal resistance, junction to case, document | 0.7 degrees C per watt, DC test at 85 degree case and 200 degree junction |
| Gate threshold voltage, document | 2.11 V at 600 microamps, 28 V drain |
| Input capacitance at 28 V, document | 34.1 pF at 1 MHz |
| Output capacitance at 28 V, document | 11.2 pF at 1 MHz, 9.7 pF at 40 V |
| Feedback capacitance at 28 V, document | 0.9 pF at 1 MHz, 0.86 pF at 40 V |
| Leakage currents, document | 1 microamp drain and 1 microamp gate, maximum |
| ESD class, document | Human body model Class 2 |
| Load mismatch, document | 10 to 1 at all phase angles, no degradation stated for the rival row of the same family |
| Document title against catalogue number | HX215078 against HXC50167, not explained by the vendor |
| Orderable addendum | None published |
| Packing quantity and moisture level | Not published |
What 70 W on a 28 V rail asks of the load and the supply
70 W into 50 ohm is 59.2 V rms and 83.7 V peak. Against a 28 V rail that is 2.99 times the supply, which is the normal arithmetic for a push pull pair in which each side drives half the load line and each drain swings to roughly twice the rail. The 90 V minimum breakdown is what gives that swing room: a 28 V part that had to swing 84 V on a single ended drain would be running at the edge of a 90 V rating, while a pair splits the same excursion between two devices.
The mismatch case is where the output network is decided. At a 2 to 1 load the peak reaches 167 V and at 3 to 1 it reaches 251 V, which is well above the 90 V drain rating and far above anything a 50 V capacitor is chosen for by instinct. The parts that fail on a 70 W board are almost never the transistor: they are the coupling capacitor, the balun and the connector, each chosen against the rail instead of against the mismatch.
The supply side is modest at this power. At 60 per cent efficiency the pair draws 116.7 W, which is 4.17 A at 28 V, and at 50 per cent it draws 140 W and 5.0 A. On a mobile radio product that is a current the alternator and the harness can carry, which is the reason the 28 V shelf exists next to the 50 V one. Put the bulk capacitance at the flange rather than at the far end of the harness, because the current step on key down is what decides whether the first pulse is clean.
Thermal: the one figure on this row that is fully published
0.7 degrees per watt is published with its test conditions, 85 degree case, 200 degree junction, DC test, which makes it usable rather than decorative. At 60 per cent efficiency the heat to move is 46.7 W, so the rise from case to junction is 32.7 degrees and at an 85 degree case the junction sits near 118 degrees against a 225 degree limit. Even at 50 per cent efficiency, where the heat is 70 W, the rise is 49 degrees and the junction sits near 134 degrees.
That margin is what separates this row from a 50 V pair at the same power. A 50 V part has a smaller current and a larger voltage swing, and the thermal path is usually the harder constraint at the flange. On this row the flange is comfortable and the effort goes into the matching network, the bias loop and the band flatness instead.
The case temperature still has to be measured rather than assumed. A thermocouple on the flange at thermal equilibrium and full power is the honest input to the calculation, and on a 70 W part in a metal housing that measurement takes ten minutes and settles an argument that otherwise runs for a week.
Drive, gain and the band the page claims
At 19 dB of gain the drive for 70 W is 0.88 W, or 29.45 dBm. At the document figure of 20 dB it is 0.70 W. Either way this is a part a small driver can push, which is why the 28 V shelf is popular in land mobile and in man portable equipment where the driver has to come from a 5 V or 12 V rail through a boost stage.
The page claims coverage from 30 MHz to 860 MHz in its application list, and the document measures one frequency, 1000 MHz. A single point measurement does not establish flatness, and an unmatched pair has an input impedance that falls with frequency, so the gain at 30 MHz and the gain at 860 MHz will not be the same as the gain at 1000 MHz. Buy a small quantity, sweep the pair on the fixture you intend to ship, and only then freeze the driver specification and the gain budget.
The application list itself is a useful procurement document. A part sold into FM broadcast, avionics at 118 to 140 MHz and TV UHF at 470 to 860 MHz is a part the vendor expects to see in volume in those sockets, and volume in a socket is what keeps a part available. When a buyer is choosing between two rows with similar data, the one with a longer application list on the vendor page is usually the one with the deeper installed base.
Where the HXC50167 sits on the shelf
The same HF to 1.5 GHz group carries a 40 W single at 28 V with 20 dB and 60 per cent, a 30 W pair at 50 V, a 25 W single at 28 V with 20 dB and 60 per cent, and this 70 W pair. In decibels the step from 40 W to 70 W is 2.43 dB and the step from 70 W to 150 W is 3.31 dB, so the group is a ladder in roughly 2 to 3 dB rungs and a system requirement lands on one rung or the next.
Read as a choice, this row is the one for a 28 V product that needs 70 W from a pair with a published thermal resistance, a published breakdown voltage and a full capacitance set, and that can live with a vendor document filed under a different name. A buyer who needs more headroom takes the 150 W single at 50 V on the same shelf; a buyer who needs less takes the 40 W single and keeps the same drive chain.
Before the purchase order goes out
Two procurement points follow. No orderable addendum is published for this row, so the tray quantity, the moisture level and the marking have to come from the vendor in writing before a production order is placed, and the incoming route that handles a document and label mismatch without stopping the line is set out on the incoming inspection plan page. Buyers comparing this row against a competitor's 70 W pair should work from the RF power transistor cross reference, which lines the two up on rail, gain and package rather than on the headline wattage. A mixed bill of materials with the driver and the passives on it can be placed through the one stop RF supply route.