VBA5415
Product Specifications
VBA5415
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBA5415 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBA5415: the 40 V version of the complementary pair
The VBA5415 is an N channel and a P channel pair in one SO-8 outline, both rated 40 V from drain to source with plus or minus 20 V on the gate, halogen free to IEC 61249-2-21. The N channel is 0.015 ohm at a 10 V gate with 6.8 A, 0.016 ohm at 8 V and 0.018 ohm at 4.5 V with 6.6 A. The P channel is 0.017 ohm at minus 10 V with 8 A, 0.019 ohm at minus 8 V and 0.022 ohm at minus 4.5 V with 5 A. Compared with the 30 V part of the same family the resistances are 30 to 40 per cent higher for 10 V more blocking capability, which is the usual trade and the reason a 24 V rail with load dump should pick this one.
The package data is shared with the 30 V sibling: 6.1 W on the N channel and 5.2 W on the P channel with the case at 25 C, 3 W each at a 25 C ambient, 2.28 W at a 70 C ambient, junction to ambient 20 C per watt on the N side and 27 on the P side for a 10 second pulse, and junction to foot 10 and 19 C per watt. The lower resistance of the P channel here against the 30 V part is worth noting, because it means the high side is not automatically the hotter one: at 5 A the P channel loses 0.43 W and the N channel at 6 A loses 0.54 W, so the two junctions sit within a few degrees of each other.
The ratings a buyer checks first
| Drain to source voltage, both channels | 40 V N, minus 40 V P |
| Gate to source voltage | plus or minus 20 V |
| On resistance, N channel | 0.015 ohm at 10 V, 0.016 at 8 V, 0.018 at 4.5 V |
| On resistance, P channel | 0.017 ohm at minus 10 V, 0.019 at minus 8 V, 0.022 at minus 4.5 V |
| Continuous drain current, summary row | 13.3 A N, 13 A P |
| Pulsed drain current, 10 microsecond | 30 A N, minus 30 A P |
| Source to drain diode current | 5.6 A N, minus 5.6 A P at 25 C case |
| Single pulse avalanche current | 20 A both channels into 0.1 mH |
| Power dissipation | 6.1 W N, 5.2 W P at 25 C case, 3 W each at 25 C ambient |
| Junction to ambient, 10 second pulse | 20 C per watt N, 27 C per watt P, 32.5 maximum |
| Junction to foot, steady state | 10 C per watt N, 19 C per watt P typical |
| Gate threshold voltage | 1 to 2.2 V N, minus 0.9 to minus 2.5 V P |
| Total gate charge at 10 V and at 4.5 V | 13.3 nC and 6.5 nC N, 13 nC and 21.7 nC P |
| Input, output and reverse transfer capacitance | 1321, 745 and 214 pF N, 1345, 792 and 245 pF P |
| Body diode forward voltage | 0.81 V N at 5.4 A, minus 0.77 V P at 2 A |
| Junction and storage range | minus 55 to plus 150 C |
Reading the electrical table instead of the front page
At 40 V the blocking margin question changes. A 24 V nominal rail with a 10 per cent tolerance and an inductive load dump can reach 40 V for a few hundred microseconds, and this part is then exactly at its rating with no margin at all, while a 30 V part would be well past it. That is why the 40 V version exists, and why the choice between the two should follow the clamp voltage of the load rather than the resistance. The gate threshold windows are the same as the 30 V sibling, 1 V to 2.2 V on the N channel and minus 0.9 V to minus 2.5 V on the P channel, so the drive conditions carry over unchanged.
The capacitance rows are where this pair separates from the lower voltage part: 1321 pF of input capacitance on the N channel against 1421 pF, and 245 pF of reverse transfer capacitance on the P channel against 25 pF. A reverse transfer figure ten times larger on the P side means the drain voltage couples into the gate far more strongly, so the Miller plateau on the high side switch lasts longer and the gate resistor has to be small enough to keep the edge clean without ringing the source inductance. The gate charge rows tell the same story: 13 nC typical on the P gate at a 10 V drive, rising to 21.7 nC in the 4.5 V column, against 6.5 nC on the N side.
The switching times are 5 ns to 17 ns on the N channel at a 10 V drive and 10 ns to 50 ns on the P channel, with the turn off delay on the P side stretching to 90 ns in the maximum column. At 4.5 V the P channel turn off delay is 40 ns typical and 70 ns maximum. For a synchronous half bridge at 100 kHz those delays set the dead time, and a driver that keeps the dead time near 100 ns will be inside the worst case window; a driver that runs 40 ns will cross conduct on a slow P channel and the loss will show up as heat rather than as a waveform. The diode recovery of 17 ns on the N side against 41 ns on the P side is the last row to read, because the slower diode is the one that needs the parallel Schottky in a continuous conduction bridge.
Where the 40 V pair belongs and where it does not
Industrial 24 V motor drive and solenoid drive are the natural home. The P channel high side can be held on indefinitely for a locked rotor test without a bootstrap refresh, the 20 A avalanche rating into 0.1 mH covers the kick from a coil, and the 40 V rating keeps a load dump clamp from turning into a board revision. A 36 V battery product is the second case, because a fully charged 36 V string reaches 42 V under charge and the 40 V part at least sits at the boundary rather than beyond it, with a clamp diode doing the rest of the work.
The part is the wrong choice for a 48 V telecom rail, where the blocking voltage has no margin at all, and it is the wrong choice for a bridge that runs above 200 kHz, because the P channel turn off tail and the 41 ns diode recovery both cost more than the resistance saves. In those two cases a single N channel pair with a bootstrap driver is the better answer, and the complementary body is only interesting when the board cannot afford a floating driver.
Sourcing notes and the second source question
The comparison that decides a complementary pair is not the resistance at 10 V but the resistance at the gate voltage the board actually provides, and at 40 V the P channel rows spread more widely between vendors than the N channel rows do. Our power management cross reference keeps both polarities in separate rows with the threshold window and the diode recovery charge beside the resistance, because a part that matches on resistance can still fail on recovery. The pin to pin cross reference carries the SO-8 bodies that share this outline, including the ones whose thermal pad routing differs.
When a customer is qualifying a replacement, how to verify a drop in replacement sets out the tests in the order that finds problems fastest: inrush into the load capacitance, gate ringing at the new resistance, dead time versus cross conduction, and junction temperature at the enclosure temperature. For a product that is already in volume and the original vendor is trimming the body, the route in the same section under last time buy keeps a line running with a date code window and a stock reservation instead of a substitute that needs a new pad.
Questions we answer before a reel is booked
Buyers ask whether the 13 A summary row applies to both halves at once. It does not. The 6.1 W and 5.2 W dissipation figures are package totals shared by two dies, and the honest continuous figure for a sealed driver is 5 A to 6 A per channel with the board acting as the heat sink. The second question is whether the part can survive a 40 V transient. It survives at the rating, which is not the same as having margin, so a rail that can ring above 40 V needs a clamp rather than a higher rated part in the same footprint.
The third question is about driving the P gate from logic. A 3.3 V or 5 V signal cannot pull the gate below a 24 V source, so a level shift device is required, and that device has to be rated for the full rail plus the ringing. The fourth is about the avalanche row. Only the current is published for this pair at 20 A into 0.1 mH; the energy rows in the sheet are printed per channel in a way that does not resolve cleanly in the text layer, and we do not quote an energy figure that we cannot read from the vendor print.
On supply, the reel carries the date code on the label and the moisture level on the packing list, the reflow window is a 260 C peak, and incoming inspection samples the resistance of both channels at 10 V and 4.5 V plus the threshold at 250 microamp. Where a customer needs the capacitance curve for an EMI study we quote it from the same document rather than from a distributor summary, and where the sheet does not print a row we say so instead of filling it in.