Contact Us

HXC50133

Brand: Hisiwell
Hisiwell HXC50133 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HXC50133 — Discrete & Power Semiconductors | Superb Automation

HXC50133

Hisiwell — Discrete & Power Semiconductors

Product Overview

The HXC50133 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

HXC50133: 17 dB of gain and 60 per cent, the row for wide pulses and high duty

The HXC50133 is a 300 W single ended LDMOS transistor on 50 V, internally matched across 0.96 to 1.215 GHz, with 17 dB of gain and 60 per cent drain efficiency on the index row. The index marks it Pulse. The vendor page says something slightly different and more useful: the part is matched for any application within the band and is aimed at avionics work where the duty cycle is high or the pulse is wide. That sentence is the reason this row exists between a 250 W CW part and a 750 W pulse part.

Gain and efficiency are the two figures that make it the easiest row in the group to use. At 17 dB the drive for 300 W is 6.0 W, which is a single small stage rather than a 100 W amplifier. At 60 per cent the drain current is 10 A and the heat is 200 W, which on a 50 V rail is the lowest current per watt in the group. Those two numbers together mean a 300 W amplifier that a two stage chain can drive and a forced air heat sink can cool.

The data sheet link on the page points at the site root and serves nothing, and the parameters block is a picture, so the capacitance set, the breakdown voltage and the thermal resistance are not readable in text. Everything below that is arithmetic is arithmetic on the index row, and the table says which is which.

The HXC50133 rows as the vendor publishes them

Part classLDMOS RF power transistor, internally matched, single ended
Output, index row300 W
Output in dBm, calculated54.77 dBm
Frequency range, index row0.96 to 1.215 GHz
Frequency range, vendor page0.96 to 1.215 GHz, any application within the band
Drain rail, index row50 V
Gain, index row17 dB
Drive required, calculated6.0 W, or 37.77 dBm
Drain efficiency, index row60 per cent
DC input at that efficiency, calculated500 W, 10.0 A at 50 V
Heat to remove, calculated200 W
Mode, index rowPulse
Duty statement, vendor pageAimed at high duty cycle or wide pulse avionics work
Output at 1 dB compressionNot published
Pulse width and duty limitNot published
Thermal resistance, junction to caseNot published in text
Transient thermal impedanceNot published
Drain to source breakdownNot published in text
Input, output and feedback capacitanceNot published in text
Load mismatch toleranceNot published
Junction temperature maximumNot published in text
Package outlineNot published in text
Class of operationNot stated on the page
Data sheet link on the vendor pagePoints at the site root, serves nothing
Parameters block on the vendor pagePublished as a picture, not as text
Orderable addendumNone published
Packing quantity and moisture levelNot published

Why high duty cycle changes which row is the right one

A pulse part is normally chosen on peak power, and duty is a footnote. On a high duty system the footnote becomes the specification. At 300 W and 200 W of heat, a 20 per cent duty cycle gives 60 W of average output and 40 W of average heat, and a 50 per cent duty cycle gives 150 W average output and 100 W average heat. A 1000 W pulse part run at 50 per cent duty would produce 500 W of average heat for the same average output, which is why a smaller, more efficient row is the better choice once duty climbs.

The other side of high duty is the supply. Ten amperes at 50 V continuous is a normal converter; the same 10 A at 50 per cent duty is 5 A average with a 10 A pulse, which any well made supply handles. Compare that with a 1000 W row: 40 A at 50 per cent duty is 20 A average, and the capacitor bank and the bus bar become the cost centre.

Wide pulses add a third factor. A long pulse lets the junction heat up during the pulse itself, so the transient impedance over the pulse width decides the peak junction temperature, not the average. Without a transient curve from the vendor, the safe approach is to derate the average heat and measure the flange during a burst at the intended pulse width.

Voltages, current and the output network

300 W into 50 ohm is 122.5 V rms and 173.2 V peak. Against a 50 V rail that is 3.46 times the supply at the connector, which is a comfortable ratio for a 50 V part and the reason the output network on a 300 W board is easier than on a 750 W one. At a 2 to 1 load the peak reaches 346 V and at 3 to 1 it reaches 520 V, so the output capacitor still has to be chosen on the mismatch case rather than on the matched case.

Ten amperes at 50 V is the supply figure, and at 60 per cent efficiency it is also close to the maximum. At 50 per cent the current rises to 12 A and the heat to 300 W, which is a 50 per cent increase in heat for a 10 point efficiency loss. The 60 per cent figure is worth protecting: keep the quiescent current where the vendor sets it, keep the gate drive clean, and do not trade efficiency for gain by raising the bias.

The thermal side is the one number a buyer can act on without the vendor. 200 W of heat with a 0.5 degrees per watt flange is a 100 degree rise, and with the flange at 85 degrees that is 185 degrees at the junction, inside a 225 degree limit. A 0.8 degree per watt flange reaches 245 degrees and is outside it. So a 300 W part on a 50 V rail needs a flange in the 0.3 to 0.5 range, and that is a specification the mechanical engineer can work to before the data sheet arrives.

Gain of 17 dB and what it saves in the chain

Six watts of drive for 300 W is the lowest drive requirement in the 960 to 1215 MHz group apart from the 90 W row. It means a single driver stage, and on a 300 W transmitter the driver can be a 10 W part running at 8 dB backoff, which is a comfortable place to be for linearity and for heat. Compare with the 750 W row at 14 dB, which needs 30 W of drive and therefore a 50 W driver, or the 1000 W row at 10 dB, which needs 100 W.

The gain also sets the stability margin. A 17 dB part with internal matching at 1 GHz has enough gain that a poor output match can return through the package and cause oscillation, so the usual precautions apply: a series resistor or a small ferrite on the gate, a well bypassed bias line, and a ground plane that stays continuous under the input match.

Gain flatness across 255 MHz is not published. On an internally matched part a decibel of tilt across the band is common, and a system that needs flat output should plan for a gain equaliser or a driver with a compensating tilt.

Where the HXC50133 sits on the shelf

The group runs 90 W, 250 W, 300 W, 750 W, 900 W narrowband and 1000 W. From 250 W to 300 W is 0.79 dB, so this row and the 250 W row are close in output and far apart in rail: 50 V against 32 V, 17 dB against 14 dB, 60 per cent against 55 per cent. From 300 W to 750 W is 3.98 dB, a full ladder step.

Read as a choice, this row is the default for a 300 W avionics or ISM amplifier that has to run at high duty or with wide pulses, driven from a single small stage. A buyer who needs continuous wave at the same power takes the 250 W row on 32 V or the 300 W row here derated, and a buyer who needs 750 W steps up and doubles the drive requirement.

Before the purchase order goes out

Three procurement points follow. No orderable addendum is published for this row, so the tray quantity, the moisture level and the marking have to come from the vendor in writing before a production order is placed, and the incoming route for a part whose duty statement is a sentence rather than a table is set out on the incoming inspection plan page. Buyers comparing this row against a competitor's 300 W L band part should work from the RF power transistor cross reference, which lines the two up on gain, efficiency and package rather than on the headline wattage. A bill of materials that carries the 6 W driver, the output passives and the bias components can be placed through the one stop RF supply route.