Contact Us

VBA4610N

Brand: VBsemi
VBsemi VBA4610N is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

VBA4610N — Discrete & Power Semiconductors | Superb Automation

VBA4610N

VBsemi — Discrete & Power Semiconductors

Product Overview

The VBA4610N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi specializes in discrete MOSFETs, power transistors, and protection devices at competitive cost for power supplies, motor control, and consumer electronics.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

VBA4610N: a dual minus 60 V P channel in one SO-8 body

The VBA4610N is a dual P channel MOSFET in a single SO-8 outline, printed at minus 60 V from drain to source and plus or minus 20 V on the gate, halogen free to IEC 61249-2-21 and built on a trench process. Each half carries 0.120 ohm at a minus 10 V gate with 3.5 A flowing and 0.145 ohm at a minus 4.5 V gate with 2.8 A flowing, which is the pair of numbers that decides whether the part works on a 12 V rail with a simple gate pull down or needs a charge pump. Continuous current is minus 4.0 A with the case at 25 C and minus 3.0 A once the case reaches 70 C, with minus 2.8 A and minus 2.1 A when the same figures are quoted to a 25 C and a 70 C ambient instead.

Putting both switches in one body matters on a battery disconnect or a dual rail load switch, because the two halves share the same footprint and the same thermal path and the board needs one placement instead of two. The catch is thermal. Each half is a small die, junction to ambient is 53 C per watt on a 10 second pulse and 85 C per watt in the steady state, and the 4.2 W dissipation is quoted with the case held at 25 C. In still air that same part is a 2 W device. A buyer who reads the 4.0 A headline and puts the part in a sealed box is reading the wrong row, and the copper under the drain pads is what closes the gap.

The ratings a buyer checks first

Drain to source voltage, each channelminus 60 V
Gate to source voltageplus or minus 20 V
On resistance at minus 10 V gate, 3.5 A0.120 ohm typical
On resistance at minus 4.5 V gate, 2.8 A0.145 ohm typical
Continuous drain currentminus 4.0 A at 25 C case, minus 3.0 A at 70 C case
Continuous drain current in still airminus 2.8 A at 25 C ambient, minus 2.1 A at 70 C ambient
Pulsed drain current, 100 microsecondminus 12 A
Continuous source to drain diode currentminus 3.9 A at 25 C case, minus 2.1 A in still air
Single pulse avalancheminus 15 A into 0.1 mH, 11.25 mJ
Power dissipation4.2 W at 25 C case, 2 W at 25 C ambient, 1.3 W at 70 C ambient
Junction to ambient, junction to foot53 and 30 C per watt typical, 62.5 and 37 maximum on a 10 second pulse
Gate threshold voltageminus 0.5 V minimum, minus 2.5 V maximum
Total gate charge at minus 10 V and minus 4.5 V20 nC and 10.1 nC typical, 30 and 15.2 maximum
Gate source and gate drain charge3.3 nC and 3.9 nC typical
Body diode forward voltage at 2.8 Aminus 0.85 V typical, minus 1.2 V maximum
Junction and storage rangeminus 55 to plus 150 C

Reading the electrical table instead of the front page

The threshold window runs from minus 0.5 V to minus 2.5 V at 250 microamp, which for a P channel means the gate has to sit 2.5 V below the source before a worst case die is guaranteed to conduct. A 3.3 V rail used directly as the gate signal therefore has 0.8 V of overdrive at the bottom of the window and no defined resistance at the top of it. On a 12 V product the gate is pulled 10 V below the source through a resistor, which is where the 0.120 ohm figure lives, and the difference between the two drive points is 21 per cent of conduction loss for a 5.5 V change in gate voltage.

Gate charge is where this die is comfortable. At 20 nC typical and 30 nC maximum on a 10 V drive, and 10.1 nC typical on a 4.5 V drive, a small driver in a SOT-23 body turns both halves without a heat sink, and 3.9 nC of gate drain charge keeps the Miller plateau short enough that a 2.2 ohm gate resistor is usually all the damping the edge needs. The turning times follow the drive: 8 ns turn on delay and 6 ns rise at a 10 V gate, against 40 ns and 28 ns at 4.5 V, and the fall time stays near 16 ns at either drive because the body diode takes over at the end of the transition. None of those figures is a switching loss budget on its own; the number that matters is the current the gate sink has to absorb, which is the charge divided by the switching period.

The body diode is the row that decides whether a half bridge survives. Forward drop is minus 0.85 V typical and minus 1.2 V maximum at 2.8 A, reverse recovery is 32 ns typical with 45 nC of recovered charge, and the diode carries minus 3.9 A continuous with the case at 25 C. Those are modest numbers, and they are the reason this part belongs in a load switch or a disconnect rather than in a hard switched bridge: a 45 nC recovery charge at 200 kHz is a real loss on a 12 V rail, and a 60 V P channel with a better diode is available for that job.

Where a minus 60 V P channel with two halves earns its place

The first case is a battery disconnect on a 24 V or 36 V pack. Two P channels in one body switch the positive lead of two rails or the two ends of a series string, the gate is pulled low through a resistor to conduct, and a small signal N channel pulls it high to interrupt. With minus 2.1 A in still air at 70 C ambient and 0.120 ohm, each half drops 0.26 V at 2 A, which is 0.5 W and 43 C of rise on the 85 C per watt steady state path. That is inside the 150 C junction with room to spare in a 60 C enclosure, and the 11.25 mJ avalanche rating covers the kick from a cable that is pulled under load.

The second case is reverse polarity protection in a product that is powered from a wall adapter and a battery at the same time. A P channel in the battery lead conducts when the adapter is present and blocks when it is not, and two halves let one body protect the pack and the load side at once. The minus 1 microamp drain current at 25 C and minus 5 microamp at 55 C is what keeps the standby budget honest, because a leaky switch on a lithium pack is a self discharge path the customer will find in the field. The third case is a two channel LED string where each half switches one branch, and there the 20 nC gate charge is the reason a tiny driver can dim at 1 kHz without visible steps.

Sourcing notes and the second source question

Dual P channel parts in SO-8 at minus 60 V are a narrow shelf, and the resistance quoted at 10 V rarely tells a buyer what the 4.5 V row will do. A competitor part at 0.10 ohm on a 10 V gate can be 0.19 ohm at 4.5 V if its threshold is wider, and a board that was tuned for one die will show a different inrush and a different turn off tail with the other. Our pin to pin cross reference starts from the tested gate voltage, the threshold maximum and the gate charge, rather than from the headline resistance. For a body that has to prove itself on the customer board, the sequence in how to verify a drop in replacement covers the four tests that catch the usual failures: inrush shape into a capacitive load, gate ringing at the new gate resistance, reverse recovery in the conducting half, and junction temperature at the case the product really reaches.

Where a customer needs the alternative to be a stock item rather than a fresh order, the power management cross reference carries the pin compatible rows with the threshold window and the thermal resistance beside them, so the choice between a drop in and a board change is visible before a sample is booked. We quote whatever the vendor print says and nothing more: this family publishes no orderable addendum, so no reel size, moisture level or marking code is invented here.

Questions we answer before a reel is booked

Buyers ask whether the minus 4.0 A rating can be used at 25 C ambient. It cannot. It is a case temperature figure, and the same die in still air is a 2.8 A switch at 25 C ambient and 2.1 A at 70 C. The second question is whether both channels can run at once. They can, but the 4.2 W dissipation is a package figure shared by the two halves, so a dual rail load switch that carries 2 A on each side is really a 1 W per channel budget at 25 C case and half of that in still air.

The third question is about the gate drive. A 4.5 V drive gives 0.145 ohm, which is 21 per cent more loss than the 10 V figure, and the threshold maximum of minus 2.5 V means a 3.3 V logic pin has to work through a pull down device rather than directly. The fourth is about the avalanche rating. The 11.25 mJ single pulse is measured into 0.1 mH with minus 15 A, and repeated events derate with junction temperature and repetition rate, so a rail that switches a solenoid every cycle still needs a clamp.

On supply, the reel is quoted with the date code printed on the label and the moisture level from the packing list, the soldering window is a 260 C peak, and the SO-8 tape orientation follows the standard outline so no feeder change is needed. Incoming inspection samples the on resistance at both gate voltages and the threshold at 250 microamp, and where a customer needs the resistance at an intermediate gate voltage we quote it from the same document rather than from a distributor summary.