HXC50131
Product Specifications
HXC50131
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXC50131 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXC50131: 90 W across 0.96 to 1.4 GHz, and the two pages disagree on where the band stops
The HXC50131 is the smallest row in the 960 to 1215 MHz group: 90 W, single ended, 50 V, internally matched, 14 dB of gain and 55 per cent drain efficiency, marked Pulse on the index. The vendor page widens the band to 0.96 to 1.4 GHz and splits the use in two: avionics from 960 to 1215 MHz, and L band from 1200 to 1400 MHz. The index row stops at 1.2 GHz. That is a 200 MHz disagreement at the top of the band, and it is the first thing a buyer should settle, because a 90 W part claimed to 1.4 GHz is a different proposition from one claimed to 1.2 GHz.
The pattern repeats on this shelf: the index trims the band and the product page widens it. The safest reading is that the index figure is the conservative one and the page figure is the vendor's intent, and an amplifier that needs gain above 1.2 GHz has to be measured rather than assumed. A sample sweep from 1.2 to 1.4 GHz on the intended fixture settles it in an afternoon.
Everything else on the row is straightforward, and a 90 W part at 50 V is the easiest point on this shelf to build. The current is 3.3 A, the heat is 74 W, the drive is 3.6 W, and the whole amplifier fits on a board that a two layer stack and a small heat sink can carry.
The HXC50131 rows as the vendor publishes them
| Part class | LDMOS RF power transistor, internally matched, single ended |
| Output, index row | 90 W |
| Output in dBm, calculated | 49.54 dBm |
| Voltage at 50 ohm, calculated | 67.1 V rms, 94.9 V peak |
| Peak against the 50 V rail, calculated | 1.90 times |
| Frequency range, index row | 0.96 to 1.2 GHz |
| Frequency range, vendor page | 0.96 to 1.4 GHz |
| Band split on the vendor page | Avionics 960 to 1215 MHz, L band 1200 to 1400 MHz |
| Drain rail, index row | 50 V |
| Gain, index row | 14 dB |
| Drive required, calculated | 3.6 W, or 35.54 dBm |
| Drain efficiency, index row | 55 per cent |
| DC input at that efficiency, calculated | 164 W, 3.27 A at 50 V |
| Heat to remove, calculated | 74 W |
| Mode, index row | Pulse |
| Application list, vendor page | ISM RF energy, with avionics and L band named in the overview |
| Output at 1 dB compression | Not published |
| Pulse width and duty limit | Not published |
| Thermal resistance, junction to case | Not published in text |
| Drain to source breakdown | Not published in text |
| Input, output and feedback capacitance | Not published in text |
| Load mismatch tolerance | Not published |
| Junction temperature maximum | Not published in text |
| Package outline | Not published in text |
| Class of operation | Not stated on the page |
| Data sheet link on the vendor page | Points at the site root, serves nothing |
| Parameters block on the vendor page | Published as a picture, not as text |
| Orderable addendum | None published |
| Packing quantity and moisture level | Not published |
A 90 W part is the cheapest way to learn this shelf
On a 50 V rail a 90 W part sits far from the supply limits that dominate the larger rows. The drain current is 3.3 A, so a 5 A converter and a modest bulk capacitor are enough. The heat is 74 W, so a 0.5 degrees per watt flange gives a 37 degree rise and a junction near 122 degrees at an 85 degree flange, well inside a 225 degree limit. The peak voltage at the connector is 95 V, so 200 V capacitors are comfortable and 100 V parts are not.
That combination makes this row a sensible first build for a team that has not used an internally matched LDMOS before. The matching is inside the package, the bias is the only external loop, and the failure modes are the ordinary ones: too little bypass on the gate, a ground plane that stops under the source, and a heat sink bolted to a flange that is not flat.
It is also the row that reveals whether the vendor's band claim holds. A sweep at 960, 1100, 1215 and 1400 MHz on one fixture tells a buyer more about the shelf than any of the larger rows, because the measurement is cheap and the result carries over.
The 1200 to 1400 MHz L band and what is there
The L band window from 1200 to 1400 MHz carries telemetry, tactical data links, some radar and a growing amount of low earth orbit satellite work. It is also the band where a 90 W part is often enough: a ground terminal or a short range link does not need 750 W, and the licensing and the power budget often cap the transmitter well below that.
The index row stops at 1.2 GHz and the page continues to 1.4 GHz, so a buyer whose product sits at 1.3 GHz is buying on the page claim. Ask for the gain and the return loss at 1.3 and 1.4 GHz before committing, and if the answer is a picture from the same page, buy ten pieces and measure them. At 90 W the cost of a sample sweep is trivial compared with the cost of a second board.
For the avionics window the position is stronger. The 960 to 1215 MHz range is named on both pages, the mode is pulse, and the application matches the row. That is the use this part was built for, and it is the use where the pages agree.
Drive, heat and the rest of the chain
3.6 W of drive at 14 dB is a single stage from a 1 W part, which makes a 90 W amplifier a two device chain with one bias loop to set. That is the practical advantage of the small rows: the driver does not become a project of its own, and the whole transmitter can be built on one board with one heat sink.
At 55 per cent efficiency the heat is 74 W, and the flange figure is again unpublished. Working from a target of 85 degrees at the flange and a 225 degree limit, the allowance is 140 degrees, which at 74 W is 1.9 degrees per watt. Almost any flange and heat sink combination meets that, which means the mechanical side of a 90 W amplifier is not the risk. The risk moves to the bias loop and to the input match, where a 14 dB part with 3.6 W of drive can be pushed into oscillation by a long gate lead.
The current is low enough that the supply is not a constraint either, which leaves the output network. At 95 V peak and 190 V at a 2 to 1 load, standard 200 V parts are fine and the network can be built from ordinary components. For a first article that is a considerable saving in both cost and schedule.
Where the HXC50131 sits on the shelf
In the 960 to 1215 MHz group the rows run 90 W, 250 W, 300 W, 750 W, 900 W narrowband and 1000 W. From 90 W to 250 W is 4.44 dB and from 90 W to 300 W is 5.23 dB, so this row is the bottom rung and the next rung is more than four decibels up.
Read as a choice, the row is for an avionics or L band transmitter in the 90 to 100 W class that wants a single driver stage, a small heat sink and a 50 V rail, and that can tolerate a band claim which the index and the page place differently. A buyer who needs 250 W takes the 250 W row on 32 V; a buyer who needs 300 W takes the 300 W row and gets 17 dB of gain as well.
Before the purchase order goes out
Three procurement points follow. No orderable addendum is published for this row, so the tray quantity, the moisture level and the marking have to come from the vendor in writing before a production order is placed, and the incoming route for a part whose band claim differs between two vendor pages is set out on the incoming inspection plan page. Buyers comparing this row against a competitor's 90 W L band part should work from the RF power transistor cross reference, which lines the two up on band, gain and package rather than on the headline wattage. A bill of materials that carries the driver, the output passives and the bias components can be placed through the RF component sourcing route.