HXN50118
Product Specifications
HXN50118
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXN50118 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXN50118: 50 W continuous from DC to 4 GHz on a 50 V rail
The HXN50118 is an unmatched gallium nitride HEMT from Hisiwell, filed on the 50 V shelf with a DC to 4 GHz window and a 50 W saturation row. Unmatched is the word that decides how the part is used: no matching network sits inside the package, so the customer board carries the whole input and output match, and that is what allows one part number to be centred anywhere inside the window instead of at one band.
50 W is 46.99 dBm by calculation, and 50 W into a 50 ohm load needs 50.0 V RMS, which is 70.7 V peak. The rail is 50 V, so the peak swing at the load sits 1.41 times the supply. That ratio is normal for a tuned class AB stage, where the drain swings above the rail on the crest of the waveform because the load line is set by the network and not by the supply, and it is the reason a 50 V part is specified with a drain breakdown far above 50 V.
What the index row does not carry is gain and efficiency. Both columns are blank for this part, which is usual across the 50 V shelf and is not the same as unavailable. It does mean that a quotation issued from the index row alone cannot promise a drive level, a DC current or a heat load, and none of the three should appear in a proposal until the data sheet has been read.
The HXN50118 rows as the vendor publishes them
| Part class | Gallium nitride HEMT power transistor, unmatched |
| Frequency range, index row | DC to 4 GHz |
| Band ratio, calculated | 4 to 1 |
| Saturation output, index row | 50 W |
| Saturation in dBm, calculated | 46.99 dBm |
| Output per gigahertz of window, calculated | 12.5 W |
| Drain rail, index row | 50 V |
| Load voltage at 50 W into 50 ohm, calculated | 50.0 V RMS, 70.7 V peak |
| Peak swing against the rail, calculated | 1.41 times |
| Mode, index row | Continuous wave |
| Modes the product page claims | Continuous wave, pulsed and any modulation |
| Gain | Not published on the index row |
| Drain efficiency | Not published on the index row |
| Package and body | Not published on the product page |
| Thermal resistance, junction to case | Not published |
| Gate bias point and quiescent current | Not published |
| Load impedance at the output | Not published, no load pull table on the page |
| Applied application list | Wireless communication infrastructure, wideband amplifier, EMC testing, ISM |
| Data sheet link on the product page | A parameter image only, no linked document |
| Orderable addendum | None published |
| Packing quantity and moisture level | Not published |
Why a DC row is not the same as a wideband part
A row that starts at DC and stops at 4 GHz is a statement about where the die is usable, not a promise of flat gain across the span. The vendor qualifies the part over that window and states no guarantee outside it. In practice a four to one window means the network on the customer board has to be changed for each band of interest, because the same shunt and series elements that present a good load at 900 MHz present a poor one at 3.5 GHz.
The advantage is procurement rather than bandwidth. One part number covers a spread of programmes, so a lab that runs EMC work from 200 MHz to 3 GHz can hold one reel instead of three band specific transistors, and a contract builder can carry one line on the shelf. The cost is that each band needs its own board and its own tuning pass, and none of that work is hidden inside the package.
There is also a thermal consequence. Efficiency on a GaN HEMT of this class moves with frequency, and with no curve published for this part the heat load at 3.9 GHz cannot be inferred from the heat load at 500 MHz. A plan that assumes a flat 60 per cent across the window and sizes the heatsink on that assumption will be short at the top of the band. The safe route is to size the thermal path from the worst measured point after the first prototype is on a bench.
Where the HXN50118 sits on the 50 V shelf
The nearest neighbours are two rows with the same DC to 4 GHz window: the HXN50117 at 40 W and the HXN50120 at 80 W. On power alone the gaps are small. The HXN50118 is 0.97 dB above the HXN50117 and 2.04 dB below the HXN50120, so the choice between them is rarely about the flagship watt figure and almost always about drive, heat and the load line the rest of the chain can support.
Read as power per gigahertz of window, the three rows come out at 10.0 W, 12.5 W and 20.0 W per gigahertz. That number is a crude way of seeing how hard the die is pushed for a given window, and it is the reason the 80 W member needs a wider drain lead and a lower thermal resistance than the 40 W member even though all three share a rail and a band.
The shelf also holds parts with published curves. The HX04200F covers DC to 4 GHz at 200 W on a 48 V rail with 20 dB of gain and 70 per cent efficiency, and the HXN50121, HXN50122, HXN50124 and HXN50126 sit on narrower windows with higher powers. Where a programme can move to 48 V or to a narrower band, a part with a published gain and efficiency column is easier to quote, because the drive budget and the heat budget can be closed from the catalogue instead of from a measurement. The comparison between these rows is laid out on the RF power transistor cross reference page.
What an order for the HXN50118 has to state, and what it cannot yet
The part carries no orderable addendum on the public page, no packing column, no marking code and no moisture level. A purchase order therefore has to name the part, the quantity, the band of use, the mode, the rail and the bias condition the amplifier will run at, and the factory has to confirm each of those back in writing. A distributor line that carries only the part number and a quantity leaves the reel size, the body and the test condition unstated.
Two of those fields matter more than they look. The band of use decides which wafer and which tuning the part is screened against, and the mode decides whether the quoted watts are a continuous figure or a pulse figure. On a DC row with a blank gain column the mode is the only published hint about the intended operating point, and the product page on this part widens it to pulsed and to any modulation, which is a broader claim than the index row makes.
Nothing published on the page allows a schedule to be quoted. Lead time, minimum quantity and the reel size all sit with the factory, and the honest answer before a reply arrives is that the date depends on a question that has not been asked yet. That is written here rather than filled in with a plausible number.
Questions buyers ask about the HXN50118
Is 50 W the continuous rating or the peak? It is the saturation row on a part listed for continuous wave, so it is a continuous figure. The vendor publishes no peak column and no average column for this part, and the product page adds pulsed and modulated use without giving a derating curve, so a modulated carrier has to come down until the junction temperature is inside the sheet and the load line still matches.
Can the part run at 28 V or 48 V instead of 50 V? Nothing published says it can and nothing says it cannot. The row states 50 V and the shelf beside it holds both 48 V and 50 V members, so a rail change is a factory question and not a catalogue answer. Asking it early matters, because a 48 V rail on a die laid out for 50 V changes the load line and the peak swing together.
What drive does it need? With gain blank on the row, no figure is quoted here. On unmatched GaN parts of this size a single driver stage of 1 to 4 W is normally enough, and a two stage driver is normally unnecessary, but the number that settles it is on the data sheet and the request for the sheet should go out with the enquiry.
Is a second source available? Not as a drop in. An unmatched GaN HEMT is defined by its die, its parasitics and its thermal path, and a substitute with the same watts at the same rail will still need its own network and its own bias point. The route that works is to qualify the second part at the same band and rail on the same board, which is what the one stop RF supply page sets out, and to keep the first part as the reference until the substitute has been measured.
Where the enquiry is a band, a rail and a power figure on one line, the fastest reply comes from sending those three together with the quantity and the schedule target, which is the form the RF component sourcing desk works from.