Contact Us

HXN40051

Brand: Hisiwell
Hisiwell HXN40051 is a discrete semiconductors component designed for DC-DC Converters & Power Supplies and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HXN40051 — Discrete & Power Semiconductors | Superb Automation

HXN40051

Hisiwell — Discrete & Power Semiconductors

Product Overview

The HXN40051 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • Low Rds(on) for minimal conduction losses in power switching
  • Fast switching speed with low gate charge for high-frequency operation
  • Avalanche-rated for robust operation under inductive load conditions
  • High junction temperature rating for demanding environments
  • Logic-level gate drive compatible for simplified design
  • RoHS and AEC-Q101 qualified options available

Key Specifications

Vds / VceV
Id / IcA
Rds(on) / Vce(sat)mΩ
QgnC
Technology—
Package—
Configuration—
Mounting—

Applications

Switch-Mode Power Supplies Motor Drives & Inverters Battery Management Systems DC-DC Converters Load Switching Automotive Power Distribution

Request Quote — In Stock, 100% New & Original, Full Warranty

HXN40051: one hundred watts at 4.4 to 5 GHz on 28 V

The HXN40051 is the 50 dBm member of the Hisiwell 4.4 to 5 GHz ladder and the largest one that still runs on the 28 V rail. The published row reads 4.4 to 5 GHz, saturated output at least 50 dBm, gain at least 10 dB, drain efficiency at least 45 per cent, 28 V, plus or minus 0.8 dB of flatness, continuous wave. Both ports are 50 ohm on a film hybrid carrier with the match synthesised in plane.

One hundred watts of radio frequency at 45 per cent efficiency draws 222.2 W from the 28 V rail, which is 7.94 A, and leaves 122.2 W of heat. Drive at the 10 dB gain floor is 40 dBm, ten watts. At this level every element of the chain is a power component: the feed, the capacitor bank, the combiner if there is one, and the cable that leaves the chassis.

The load voltage into 50 ohm at saturation is 70.7 V RMS and 100 V peak. That is a number worth stopping on. A hundred volts peak is beyond the rating of many laboratory attenuators and of most coaxial connectors built for instrumentation, and the ordinary answer is a rated load, a directional coupler and an isolator rather than a direct connection to a spectrum analyser.

The part is the natural final stage for a C band link amplifier, a radar transmitter at moderate duty or a laboratory source that has to drive a high level mixer. Where the output has to go higher on this band, the next member raises the rail to 32 V and the member after that is pulsed.

The parameter rows Hisiwell publishes for HXN40051

Part classGallium nitride power transistor, internally matched
Frequency range4.4 to 5 GHz
Bandwidth, calculated600 MHz, 12.8 per cent fractional at a 4.70 GHz centre
Saturation output power as publishedat least 50 dBm
Saturation output power in watts, calculated100.00 W
Gain as publishedat least 10 dB
Drain efficiency as publishedat least 45 per cent
Drain voltage28 V
Flatness across the bandplus or minus 0.8 dB
Operating modecontinuous wave
Input impedance50 ohm
Output impedance50 ohm
Match technology as described by the vendorin plane matching synthesis, film hybrid integration
Output at 1 dB compressionnot published, the index prints a slash
DC input at saturation, calculated222.2 W
Drain current at saturation, calculated7.94 A at 28 V
Dissipation at saturation, calculated122.2 W
Dissipation if efficiency falls to 40 per cent, calculated250.0 W
Drive power for the rated output, calculated40 dBm, 10.00 W
Output per 100 MHz of the band, calculated16.67 W
Load voltage at saturation into 50 ohm, calculated70.7 V RMS, 100.0 V peak
Thermal resistance, junction to casenot published
Package outline and dimensionsnot published in text, one image on the product page
Scattering parametersnot published
Pinch off voltage and gate bias pointnot published
Operating and storage temperaturenot published
Moisture level and floor lifenot published
Orderable addendum and packingnot published
Neighbour on the same band at 47 dBmHXN40050, same rail, 11 dB gain
Neighbour on the same band at 51 dBmHXN40052, 32 V rail, 10 dB gain

One hundred and twenty two watts on a carrier

At 3 C per watt the rise over the case would be 367 C and at 5 C per watt 611 C, so this part only runs at saturation on a carrier whose thermal resistance is far below 1 C per watt. That means a copper tungsten or copper molybdenum carrier, a spreader, and a sink sized by measurement rather than by a published curve, because the vendor does not publish junction to case.

The usual practice is not to run it at saturation continuously. At 6 dB backoff the output is 25.1 W and the dissipation, at an assumed 30 per cent efficiency in backoff, is 58.6 W, which is a workable figure on a metal block. Many C band link amplifiers sit exactly there for linearity rather than for heat.

The efficiency floor is again the number to quote: at 40 per cent the dissipation is 250 W, twice the published point. A five point miss on efficiency is a factor of two on the heat, and that factor is what the mechanical group has to be told at the proposal stage.

The drive chain behind a ten watt input

Ten watts of drive is the largest requirement on this band, and it is the reason the family has a 47 dBm member. A chain of 37, 43 and 47 dBm stages on the same 28 V rail delivers 40 dBm with a 3 dB margin at the final driver, using one transistor family and one rail across the whole chassis.

Gain falls by 1 dB at this rung against the member below, so the driver budget grows by 1 dB while the output grows by 3 dB. That is a favourable trade, and it is why a 100 W stage is usually built as 10 W driver plus 100 W final rather than as two 50 W devices.

Where a cross reference is being done, the drive level is the field that catches people out. A competitor part with 13 dB gain at the same output needs 2.5 W of drive, and a replacement with 10 dB needs 10 W. Our RF power transistor cross reference page puts gain immediately after rail and mode for that reason.

Protection, mismatch and the hundred volt output

The vendor publishes no load mismatch tolerance, no absolute maximum table and no overdrive rating. At 100 V peak into a matched load, a 2:1 mismatch raises the peak to roughly 135 V, and a 3:1 mismatch to about 160 V. An isolator rated for the band and the power is the ordinary protection, and a circulator with a load is the cheaper version where space allows.

The drain feed carries 7.94 A. A choke that saturates, a ground return with inductance, or a capacitor bank with insufficient ripple current all show up as a slow failure rather than an immediate one, which is the hardest kind to diagnose in the field.

The gate side needs the same care in the other direction. Ten watts of drive at the input means an exciter fault can deliver enough power to damage the input match before any protection reacts, so a limiter or a directional coupler with a detector belongs in front of the stage.

What a hundred watt build needs on the drawing

The mechanical drawing is the only place the package is defined, and it is an image rather than text, so the footprint, the flange thickness and the screw pattern have to be read from it and checked against the carrier. The electrical rows do not define any of that.

The bias network is not published as a circuit or a value set, so it has to be built and measured. What the vendor does state is the 28 V rail and the 50 ohm port impedance, which fixes the external environment the part expects.

Our RF component sourcing page lists the documents we ask for when a customer is building around a part like this: the drawing, the tooling, the reel format and the factory confirmation of the rail and the mode.

Questions buyers ask about HXN40051

Is it available on a 32 V rail. Not in this band as published. The 51 dBm member is the 32 V part, and the rail step is how the vendor gets the extra 1 dB without raising the current further.

Can it be pushed to 51 dBm by overdrive. The published figure is a floor at saturation on 28 V, and the vendor gives no overdrive allowance, so a 1 dB push is outside the document. Where 51 dBm is required the 32 V member is the honest route.

What is the pulse capability. The row says continuous wave. Pulsing lowers the average heat but does not raise the saturated output beyond the published floor, and the vendor publishes no pulse width or duty limit for this part.

How is it supplied and quoted. Through the RF procurement route, with the band, rail, mode and quantity on the request, and with the packing confirmed by the factory because the vendor page carries no orderable addendum.