VBC7P2216
Product Specifications
VBC7P2216
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBC7P2216 from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBC7P2216: a 30 V P channel in a TSSOP8 body
The VBC7P2216 is a single P channel MOSFET rated at minus 30 V drain to source, with a plus or minus 20 V gate window and a threshold of minus 1.7 V. It carries minus 9 A, and its on resistance is 20 milliohm at a 4.5 V gate and 16 milliohm at 10 V, on trench silicon in a TSSOP8.
A P channel is chosen when the switch has to sit on the high side of a rail and the gate has to be pulled below the source to turn it on. That convenience costs area: for the same die size a P channel has roughly twice the on resistance of an N channel, and this part shows the ratio plainly, since 20 milliohm at 4.5 V is more than twice the 9 milliohm of the N channel part in the same body and the same voltage class.
What the P channel buys is a gate that can be driven from the rail it switches, through a resistor and a small N channel, without a bootstrap capacitor or a charge pump. On a 5 V or 12 V rail that simplification is often worth the resistance.
Key data for the VBC7P2216
| Configuration | Single P channel |
| Package | TSSOP8, 0.65 mm pitch |
| VDS | Minus 30 V |
| VGS | Plus or minus 20 V |
| Vth | Minus 1.7 V typical |
| ID | Minus 9 A |
| RDS(on) at 4.5 V | 20 milliohm |
| RDS(on) at 10 V | 16 milliohm |
| Technology | Trench |
| Gate charge | Not published on the catalogue page |
| Body diode | Intrinsic, cathode at drain, which is the direction that matters for a reverse polarity block |
| Catalogue note | The vendor page prints the parameter table under this code but the descriptive paragraph names VBC7P3017, so confirm the exact suffix before a purchase order |
The sign conventions that catch people out
Every number on a P channel is negative except the gate window, and that is where mistakes enter a bill of material. A minus 30 V rating means the drain sits 30 V below the source. The threshold of minus 1.7 V means the gate has to be 1.7 V below the source before the channel starts to form. A positive threshold copied from an N channel table would put the part permanently on, or permanently off, depending on which way the rail falls.
The gate window of plus or minus 20 V is measured from the source, not from ground. On a 12 V rail with the source at 12 V, a gate pulled to ground is 12 V below the source, which is inside the window. On a 24 V rail the same pull would be 24 V, outside it, and the gate needs a divider or a zener. That is the calculation that decides whether a P channel can be driven directly from a rail or needs a small circuit around it.
There is also a catalogue discrepancy worth naming. The vendor page carries the parameter table under this code, and the descriptive paragraph on the same page refers to a different suffix in the same family. The electrical values agree with the table, but a purchase order should carry the exact string and a confirmation against the supplier record, not a family name.
Thermal behaviour of a P channel in this body
At 20 milliohm and 2 A the part drops 40 millivolt and dissipates 80 milliwatt. At 5 A it dissipates half a watt, which in a TSSOP8 with the lead frame soldered to a modest pad puts the junction 30 to 40 degrees above ambient. That is the point where the 9 A headline stops being a working number.
The reason is die area. To reach 20 milliohm a P channel needs a larger die than an N channel of the same resistance, and a larger die in the same eight lead body means the heat has further to travel to the leads. The package thermal resistance does not improve just because the silicon is bigger.
In a reverse polarity block the P channel carries the whole load continuously, which is the worst case for this body. In a load switch that is on for a fraction of the duty cycle, the same part is comfortable. The application decides, not the rating.
Checking a replacement against the sign and the curve
When a P channel is replaced, three things have to match before anything else is compared. The sign and magnitude of the threshold, the gate window measured from the source, and the direction of the body diode. A candidate with the same resistance and the opposite body diode orientation will protect nothing, and it will not be obvious on a bench test until the rail is reversed. Our how to verify a drop in replacement page walks through that sequence.
The fourth item is the transfer curve below the published gate voltage. A P channel driven from a 3.3 V logic pin through a resistor sees 3.3 V of overdrive only if the source is at the same rail. As soon as the source sits at 5 V and the gate is pulled to a 3.3 V pin, the overdrive is 1.7 V whatever the gate pin does, and the resistance at that point is what governs the drop.
The sourcing side of this part is covered on the component lead time solutions. For a P channel that is often single sourced, that page covers how a date is quoted and what is confirmed before it is promised.
Questions we get on this code
Is a P channel better than an N channel plus a charge pump? Cheaper and simpler, yes. Better, only at low current. Above about 3 A the resistance penalty outweighs the circuit saving, and the N channel with a small driver wins on loss.
Can it block reverse polarity on its own? Yes, with the gate tied to the source through a resistor and pulled down by a small N channel or a zener. The body diode orientation is what makes the block work before the channel turns on.
What is the difference between this code and the other suffix in the same family? The catalogue page does not separate them in the table. We treat the descriptive paragraph as unconfirmed and quote against the exact string on the request, with the supplier record attached.
Is the part suitable for a 24 V rail? Only with a gate clamp. The drain rating has no margin on 24 V and the gate window is exceeded if the gate is pulled to ground from a 24 V source.