HXC50111
Product Specifications
HXC50111
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HXC50111 from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HXC50111: 600 W with a 900 MHz band edge, the top of the HXC50 shelf
The HXC50111 is a Hisiwell LDMOS RF power transistor at 300 W per device, two devices per pair and a band edge at 900 MHz, which is the highest edge on the HXC50 shelf. The vendor page calls it a 600 W capable, highly rugged, unmatched LDMOS FET covering HF up to 900 MHz, usable in pulse and CW, and the index marks the mode as CW Enhanced rather than plain CW. That label is the one thing on this row that no other row in the same band carries, and nothing on the page defines what it changes.
A 600 W pair at 900 MHz is a harder build than a 600 W pair at 500 MHz, and the difference is not in the transistor. It is in the network, the capacitors and the tolerance stack. At 900 MHz a 3 mm line length is a meaningful fraction of a wavelength, a 1 pF capacitor is 177 ohm of reactance, and the package parasitics are no longer small compared with the matching elements. Every one of those turns a bench result into a build that has to be measured rather than copied.
The row and the page agree on 600 W and on the 900 MHz edge. Neither publishes gain, efficiency, pulse width, duty cycle, thermal resistance, load pull, package or an orderable addendum. What follows separates the published figures from the arithmetic and marks every assumption.
The HXC50111 rows as the vendor publishes them
| Part class | LDMOS RF power transistor, unmatched, two devices in a pair |
| Frequency range, index row | HF to 0.9 GHz |
| Frequency range, vendor page | HF up to 900 MHz |
| Highest band edge on the HXC50 shelf | 900 MHz, this row |
| Output per device, index row | 300 W |
| Output for the pair, calculated | 600 W |
| Output in dBm, per device, calculated | 54.77 dBm |
| Output in dBm, pair, calculated | 57.78 dBm |
| Step from one device to the pair, calculated | 3.01 dB |
| Load voltage at 600 W into 50 ohm, calculated | 173.2 V rms, 244.9 V peak |
| Peak against the 50 V rail, calculated | 4.90 times |
| Peak at a 2 to 1 mismatch, calculated | 489.9 V |
| Peak at a 3 to 1 mismatch, calculated | 424.3 V |
| DC input at 55 per cent, calculated | 1090.9 W |
| Drain current at 50 V and 55 per cent, calculated | 21.82 A |
| Heat to remove at 55 per cent, calculated | 490.9 W |
| DC input at 65 per cent, calculated | 923.1 W |
| Drain current at 50 V and 65 per cent, calculated | 18.46 A |
| Heat to remove at 65 per cent, calculated | 323.1 W |
| Step against the 260 W pair on the same shelf, calculated | 3.63 dB |
| Mode, index row | CW Enhanced |
| Modes named on the page | Pulse and CW |
| Meaning of CW Enhanced | Not defined on the row or the page |
| Gain, index row | Not published |
| Efficiency, index row | Not published |
| Drain rail, both sources | 50 V |
| Thermal resistance, junction to case | Not published |
| Load impedance and load pull | Not published |
| Package and drawing | Not published |
| Orderable addendum and packing | None published |
| Applications listed on the page | Industrial, scientific and medical, VHF communication, UHF TV, aerospace |
What 600 W at 900 MHz asks of the network
600 W into 50 ohm is 173.2 V rms and 244.9 V peak, which is 4.90 times the 50 V rail. That ratio is lower than on the 500 MHz rows because the power is lower, not because the part is more robust. On an unmatched device the drain sees a transformed load well below 50 ohm, so the current in the output network is high even though the voltage at the connector is moderate, and that current is what sets the capacitor rating.
At 900 MHz the matching section is short. A quarter wave at 900 MHz in a 0.762 mm laminate with a dielectric constant of 3.5 is about 44 mm, and a shunt capacitor of 10 pF is 17.7 ohm at that frequency. Those numbers mean the network can be trimmed with a file and a scalpel, which sounds convenient and is a warning: two builds from the same drawing and a 2 mm difference in line length will not make the same power. Build the first article with the ability to measure and adjust, then freeze the drawing.
The 2 to 1 mismatch case raises the peak at the load to 489.9 V and the current correspondingly. At 900 MHz a mismatch also changes the impedance seen by the drain through the network, so the device can be asked to deliver power into a load it cannot drive at that frequency. Protection in the control loop is not optional at this edge, and the reflected port should be watched on every first article rather than only on the failed ones.
The heat at 55 per cent is 490.9 W, 245 W per flange, and at 65 per cent it is 323.1 W, 162 W per flange. The lower figure is plausible for a 50 V LDMOS at HF but it is an assumption, because no efficiency is published for this row. Size the cold plate for the 490 W case and the result will be quiet rather than marginal.
What CW Enhanced may mean, and what to ask
The index carries two rows marked CW Enhanced, this one and the 260 W pair, and no other row on the shelf carries the label. The page does not define it. It could mean a die with a different termination for better ruggedness under continuous drive, a screening step at the factory, or a bin selected for lower drift over time. Each of those has a different consequence for the buyer, and none of them can be read off the row.
The practical approach is to ask three questions of the factory: what changes in the die or the package between this row and the plain CW row at similar power, what test distinguishes the two at incoming inspection, and whether the label carries a longer or a different warranty. If the answers are that the die is the same and only the screening differs, the label is a quality claim and not a performance claim, and it should be priced accordingly.
Until those answers arrive, treat CW Enhanced as a name rather than a specification. Do not build a lifetime argument on it, and do not assume it replaces a thermal calculation, because a label cannot lower a junction temperature.
The shelf around the HXC50111
| HXC50111, 300 W per device, to 900 MHz | 600 W, 57.78 dBm, CW Enhanced |
| HXC50109, 130 W per device, to 1 GHz | 260 W, 54.15 dBm, CW Enhanced |
| HXC50114, 500 W per device, to 500 MHz | 1000 W, 60.00 dBm, 500 MHz edge only |
| HXC50113, 450 W per device, to 500 MHz | 900 W, 59.54 dBm, 500 MHz edge only |
| HXC50104, 650 W single ended, to 500 MHz | 650 W, 58.13 dBm, one flange |
| HXC50101, 200 W single ended, to 800 MHz | 200 W, 53.01 dBm, published data sheet |
| HXC50175, 115 W per device, to 1 GHz, 28 V | 230 W, 53.62 dBm, 15 dB, 65 per cent |
| HXC50169, 70 W per device, to 1 GHz, 28 V | 140 W, 51.46 dBm, 18 dB, 60 per cent |
The comparison that matters most is against the 260 W pair marked with the same label. It is 3.63 dB below, one device bin smaller, and cheaper. Where a system needs 600 W it will not use the 260 W part, but where a system needs 300 W it can use either a single 300 W device or a 260 W pair derated, and the pair has the advantage of being a row the factory has already marked for continuous drive.
The other comparison worth making is against the 500 MHz rows. A 900 W or 1000 W pair at 500 MHz is not interchangeable with this part at 900 MHz even though the power is higher, because the network, the capacitors and the connector are all different at the higher edge. Buyers who compare only the power column end up with a part that cannot be matched in the box they have.
Incoming inspection and first article at 900 MHz
The first article at this edge needs a fixture that can be measured, not a fixture that can be copied. Start with the vendor's typical performance if one can be obtained, build the network for the sub band of interest, and measure gain, output and drain current at three frequencies across that sub band. A pair that makes 600 W at the centre and 480 W at the top of the sub band is normal for a single section network, and the difference is what tells the buyer whether the sub band is narrow enough for the system.
The incoming inspection plan covers the DC checks, the marking and the quiescent current. At 900 MHz it should be extended with a phase measurement between the two legs of the pair, because a phase error that is harmless at 500 MHz can cost most of a decibel here, and with a reflected power reading at full drive, because the network is more sensitive to load at the higher edge.
Where the part goes into a product that must hold its output over temperature, measure the first article hot as well as cold. A 600 W pair with 490 W of heat inside the enclosure will run its own network hotter than the bench fixture does, and the capacitor values that worked on the bench will move. That is the failure mode that shows up in the field rather than in the incoming test, and it is cheaper to find on a first article.
Questions buyers ask about the HXC50111
Is the pair 600 W or 300 W? The pair is 600 W, 57.78 dBm. The row is 300 W times two, and one device is 300 W, 54.77 dBm.
What does CW Enhanced mean? Nothing on the row or the page defines it, and only two rows on the shelf carry it. Ask the factory what changes and how it is screened before paying a premium for the label.
Does it cover the whole HF to 900 MHz range at 600 W? The row states one power for the range. A single network will not hold it across the full band, so the power quoted applies to a sub band cut for the system, and the edges have to be measured.
What supply and current? 50 V, and 21.82 A at 55 per cent efficiency or 18.46 A at 65 per cent, both calculated rather than published.
How much drive is needed? Not published. At 15 dB it is 19 W for 600 W, at 18 dB it is 9.5 W. Ask the factory for the gain of the screened row rather than the class figure.
Is there a document? No data sheet, no orderable addendum and no packing data are published for this row. The 200 W single ended row on the same shelf does carry a full document, so the format exists at this factory even if it is not applied here.
To price the HXC50111 against the 260 W row and the 500 MHz parts, send the sub band, the quantity and the rail to the RF component sourcing desk. Where the part replaces an incumbent, the cross reference page is the place to start, and where several devices have to be matched into one amplifier the RF supply page sets out how a matched set is bought rather than a bag of parts.