HX27240F
Product Specifications
HX27240F
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HX27240F from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HX27240F: a 240 W row with two efficiency figures that differ by a factor of ten in heat
The HX27240F is a gallium nitride power transistor on the 48 V side of the 50 V shelf, covering 1.8 to 2.7 GHz with a 240 W row, 18 dB of gain and 80 per cent drain efficiency. On the index row it reads like a base station final, and the page supports that: it describes the part as a 240 W device for wireless base stations, with input pre-matching, a broadband response and a thermal flange package on a 48 V rail.
The parameter block on the same page tells a different story, and it is the most useful thing on the page. It publishes a peak output of 190 W, a linear efficiency above 24 per cent, a linear gain above 15 dB and an adjacent channel power ratio below minus 38 dBc. Those are linear figures, measured with a modulated signal at a stated adjacent channel limit, and they are not comparable with the 240 W and 80 per cent on the row.
The gap between the two sets is not a vendor error. It is the difference between a device driven into compression and the same device backed off until it is linear enough for a modulation standard, and it changes the heat load from 60 W to 602 W on the same part.
The HX27240F rows as the vendor publishes them
| Part class | Gallium nitride power transistor, input pre-matched |
| Frequency range, index row | 1.8 to 2.7 GHz |
| Frequency range, product page prose | 800 to 2700 MHz |
| Window width on the index row, calculated | 900 MHz |
| Band ratio on the index row, calculated | 1.5 to 1 |
| Band ratio implied by the prose, calculated | 3.4 to 1 |
| Saturation output, index row | 240 W, 53.80 dBm |
| Peak output, product page parameter block | 190 W, 52.79 dBm |
| Gap between the two power figures, calculated | 1.01 dB |
| Output per megahertz of the 900 MHz window, calculated | 0.27 W |
| Gain, index row | 18 dB |
| Linear gain, product page parameter block | Above 15 dB |
| Drive at 18 dB, calculated | 3.80 W, 35.80 dBm |
| Drive at 15 dB for 190 W, calculated | 6.01 W, 37.79 dBm |
| Drain efficiency, index row | 80 per cent |
| Linear efficiency, product page parameter block | Above 24 per cent |
| DC input at 240 W and 80 per cent, calculated | 300 W |
| Heat at 240 W and 80 per cent, calculated | 60 W |
| DC input at 190 W and 24 per cent, calculated | 791.7 W |
| Heat at 190 W and 24 per cent, calculated | 601.7 W |
| Drain current at 48 V in the linear case, calculated | 16.49 A |
| Adjacent channel power ratio, product page | Below minus 38 dBc |
| Drain rail, index row | 48 V |
| Load voltage at 240 W into 50 ohm, calculated | 109.5 V rms, 154.9 V peak |
| Peak against the rail, calculated | 3.23 times |
| Mode, index row | CW |
| Test signal for the linear figures | Not published |
| Peak to average ratio assumed | Not published |
| Package, flange and body | Thermal flange package, no drawing published |
| Thermal resistance | Not published |
| Load impedance and load pull | Not published |
| Data sheet | No document linked from the page |
| Orderable addendum | None published |
| Packing quantity and moisture level | Not published |
| Applications listed | Wireless base stations, low band applications, RF and microwave systems |
Two efficiency figures, one part, and a chassis between them
80 per cent at 240 W means 300 W of DC input and 60 W of heat. 24 per cent at 190 W means 791.7 W of DC input and 601.7 W of heat. Both are on the same page, both are true at their own condition, and they are 10 times apart in the number that decides the heatsink, the fan and the rack space.
The condition that separates them is linearity. A modulated signal with a high peak to average ratio puts the average power far below the peak, and the amplifier has to stay linear at the peak, which means it runs backed off. Backed off, a GaN device loses drain efficiency quickly, and 24 per cent at 190 W is a normal figure for that regime. Driven into compression for a continuous wave tone, the same die reaches 80 per cent at 240 W.
So the question for the buyer is not which number is right. It is which one describes the amplifier. A continuous wave industrial or ISM source runs near the 80 per cent figure. A base station or a linear transmitter runs near the 24 per cent figure and carries a heat load ten times larger. A quotation that picks one without naming the signal is a quotation that will be wrong for one of the two customers.
The window on the row and the window in the prose
The row says 1.8 to 2.7 GHz, a 1.5 to 1 window. The prose says 800 to 2700 MHz, a 3.4 to 1 window. Those are not the same part, and the difference is the whole low band from 800 MHz to 1.8 GHz, which is where a great deal of the base station market sits. Read the prose as a description of the market the part is aimed at and the row as the qualified window, and the discrepancy resolves, but only if the buyer reads both.
The safe handling is to treat 1.8 to 2.7 GHz as the qualified range and to ask the factory for a statement about anything below 1.8 GHz. If the part really does cover 800 MHz, that is a finding worth having in writing before a programme is built on it. If it does not, the prose is marketing language and the row is the specification.
Either way the window decides the network, because a 1.5 to 1 match is a different problem from a 3.4 to 1 match, and the pre-matching inside the package is only claimed for the part the page describes.
Where the HX27240F sits on the 48 V shelf
The nearest rows are the 2 to 3 GHz and 2 to 4 GHz group. The HX30370P is 370 W over 2 to 3 GHz with 18 dB and 78 per cent, 1.88 dB above this row. The HX2040185P is 185 W over 2 to 4 GHz with 18 dB and 70 per cent, 1.13 dB below it but covering more than twice the window. The HX2040370P is 370 W over 2 to 4 GHz, which is both more power and a wider window at a lower efficiency.
Against those, the HX27240F is the base station shaped row: narrow window, high efficiency at compression, a published linear figure with an adjacent channel limit, and an input pre-match. For a linear transmitter that is the most useful set of columns on the shelf. For an ISM source that runs continuous wave, the higher power rows are cheaper per watt. The comparison across the 48 V group is on the RF power transistor cross reference page.
What an order for the HX27240F has to state, and what it cannot yet
No orderable addendum, packing quantity, marking code or moisture level is published, and no data sheet or thermal resistance is available. The purchase order has to carry the part number, the window the amplifier will use inside the 1.8 to 2.7 GHz range, the rail, the signal (continuous wave, or the modulation with its peak to average ratio), the linearity limit, the quantity and the incoming test. The signal is not optional here: it decides whether the heat load is 60 W or 602 W.
The incoming gate should measure gain and output at the operating point the system will use, with the signal the system will use. A continuous wave sweep will pass a device that fails on a modulated signal, and the difference only shows up when the adjacent channel figure is measured. The incoming inspection plan page sets out how to size that gate, and the RF component sourcing page covers the trace and the batch record.
Questions buyers ask about the HX27240F
Is it a 240 W part or a 190 W part? Both, at different conditions. 240 W is the saturated row, 190 W is the peak figure in the linear parameter block, and the 1.01 dB between them is smaller than the difference in the heat load.
Which efficiency do I use for the heatsink? The one that matches the signal. 80 per cent belongs to a continuous wave stage at compression, 24 per cent to a linear stage backed off for adjacent channel power. The second case is ten times the heat.
Does it cover 800 MHz? The row says 1.8 to 2.7 GHz and the prose says 800 to 2700 MHz. Ask the factory for a written statement before committing below 1.8 GHz.
Is the input matched? The page claims input pre-matching, which is one of the few matching claims on this shelf that is specific about which port. The output match remains on the board. Where the whole chain is bought against one date, the one stop RF supply page covers the consolidated order.