VBGQF1101N
Product Specifications
VBGQF1101N
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBGQF1101N from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBGQF1101N: 100 V in a three millimetre square DFN
The VBGQF1101N is a single N channel MOSFET rated at 100 V drain to source, with a plus or minus 20 V gate window and a threshold of 2.5 V. It carries 50 A and its on resistance is 13.5 milliohm at a 4.5 V gate and 10.5 milliohm at 10 V. The silicon is a shielded gate structure and the body is the DFN 3 by 3 millimetre package with an exposed pad.
The combination is unusual enough to be worth stating plainly. A 100 V die with 10.5 milliohm of resistance fits in a body that is smaller than the TSSOP8 that holds a 30 V part at 7 milliohm. That is what a shielded gate structure buys, and it is why this class of package now appears on 48 V and 60 V boards that used to need a TO252.
The 50 A figure is a die and lead frame number at a 25 C case with the pad soldered to a good copper area. In the three millimetre body the practical continuous current in still air is a fraction of that, and the copper under the pad is the rating rather than the package alone.
Key data for the VBGQF1101N
| Configuration | Single N channel |
| Package | DFN 3 x 3 mm, eight pads plus exposed pad |
| VDS | 100 V |
| VGS | Plus or minus 20 V |
| Vth | 2.5 V typical |
| ID | 50 A |
| RDS(on) at 4.5 V | 13.5 milliohm |
| RDS(on) at 10 V | 10.5 milliohm |
| Technology | Shielded gate trench |
| Gate charge | Not published on the catalogue page |
| Body diode | Intrinsic, from the exposed pad drain to the source pads |
| Thermal path | Exposed pad, so the copper island and the via array under it set the rating |
The 4.5 V to 10 V gap tells you about the drive
Between the two published gate voltages the resistance falls from 13.5 to 10.5 milliohm, about 22 per cent. That is a moderate gap for a 100 V part and it says the device was characterised for a 5 V gate driver as well as a 10 V one. On a board that drives from a 5 V rail the 13.5 milliohm column is the one to use, and the conduction loss at 8 A is 0.86 watt rather than 0.67.
The threshold of 2.5 V leaves 2 V of overdrive at a 4.5 V gate. That is workable, and it is not the same as a real logic level part with a 1.5 V threshold. A 3.3 V pin on this device gives 0.8 V of overdrive, which is a region where the resistance is several times the published figure and where the part drifts with temperature as the threshold falls.
For a synchronous buck the low side device is driven by the same 5 V rail as everything else on the board, so the 13.5 milliohm column is the honest one. The high side device sees the bootstrap rail and reaches 10 V, which is where the 10.5 milliohm applies.
Ten milliohm in a nine square millimetre body
At 8 A the part dissipates 0.86 watt at a 4.5 V gate. The DFN 3 by 3 body with the pad soldered to four square centimetres of copper on two layers has a junction to ambient resistance around 45 to 55 degrees per watt, so that wattage puts the junction 40 to 50 degrees above ambient. At 15 A it is 3 watt and the body needs a via array and a thermal plane, not just a pad.
The exposed pad is the only real thermal path and it is on the drain. That means the copper island under the part is at the switch node potential, which has two consequences. The island has to be sized for the switching noise it will radiate, and any thermal via array in it has to be evaluated as part of the high frequency loop rather than as a heat path alone.
For a 100 V part the creepage between the pad and the gate pad is small, and the pad edges carry the full 100 V. Solder mask over the island helps, but the gap between the pad and the surrounding copper is part of the voltage rating of the assembly, not only of the package.
Why a 100 V part ends up in a small body
The reason is usually current density. A 48 V board with a hot swap stage or a 60 V battery tool with a small control board cannot afford a TO252, and a shielded gate die at 10 milliohm lets the switch sit next to the controller. Our kitting service page covers how the small switches, their gate resistors and the passive parts around them are grouped for a line that builds several variants of one board.
The trade is thermal, and it is made deliberately. A board that puts 3 watt into a three millimetre body has to give that heat somewhere, and the answer is copper on the board rather than a heatsink on the part. That is a board level decision, and it has to be made before the copper is drawn, not after the first thermal test.
The sourcing side of this part is covered on the one stop BOM sourcing. For a small body switch that ships beside its controller and passives, that page covers how the group is sourced together.
Questions we get on this code
Is the 50 A usable without a heatsink? No. With the pad on a good copper island the continuous figure is nearer 10 to 15 A in still air, and the 50 A number assumes a case held at 25 C.
Can it replace a 60 V part in the same body? Only if the board needs the extra voltage. The 100 V die has more resistance than a 60 V die of the same size, so a replacement in the other direction is a downgrade in conduction and an upgrade in margin.
How should the pad be connected? To a copper island with a via array to an inner plane, with the loop area between the island and the input capacitor kept small. The pad is the drain and it is also the switch node, so its area is a noise decision as much as a thermal one.
What is the packing? The DFN 3 by 3 body normally ships 3000 or 5000 pieces on a large reel depending on the supplier record. We confirm the reel size on the quotation.