VBM18R06SE
Product Specifications
VBM18R06SE
VBsemi — Discrete & Power Semiconductors
Product Overview
The VBM18R06SE from VBsemi is a discrete power semiconductor delivering efficient switching and power conversion. VBsemi (微碧半导体) specializes in discrete MOSFETs, power transistors, and protection devices for power supplies, motor control, and consumer electronics.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
VBM18R06SE: 800 V and 6 A in a TO220
The VBM18R06SE is a single N channel MOSFET rated at 800 V drain to source with a plus or minus 30 V gate window and a threshold of 3.5 V. It carries 6 A and its on resistance is 750 milliohm at a 10 V gate. The silicon is a deep trench super junction structure and the body is the TO220 through hole package.
Eight hundred volts at 750 milliohm and 6 A is a small offline switch. At 1 A it drops 0.75 V and dissipates 0.75 watt; at 2 A it is 3 watt and the tab needs a heatsink. So the working current is 0.5 to 1 A continuous, with the 6 A rating reserved for the start up pulse and for short overloads.
The body is through hole, which for a part this size is a deliberate choice. A TO220 bolts to a heatsink and it survives the thermal cycling of an offline converter better than a surface mount tab of the same die, which is why this class of part still appears in industrial supplies.
Key data for the VBM18R06SE
| Configuration | Single N channel |
| Package | TO220, three lead through hole with tab |
| VDS | 800 V |
| VGS | Plus or minus 30 V |
| Vth | 3.5 V typical |
| ID | 6 A |
| RDS(on) at 10 V | 750 milliohm |
| Technology | Deep trench super junction |
| Gate charge | Not published on the catalogue page |
| Body diode | Intrinsic, with a fast recovery that suits a flyback |
| Mounting | Tab bolted or clipped to a heatsink, drain at tab potential |
| Isolation | A thermal pad or a mica washer is needed when the heatsink is earthed |
Seven hundred and fifty milliohm is a loss budget
The resistance sets everything about how this part is used. At 0.5 A the loss is 188 milliwatt and the TO220 runs cool with no heatsink at all. At 1 A it is 0.75 watt and the tab rises about 40 degrees on a small clip on sink. At 2 A it is 3 watt and the part needs a real sink. At 6 A it is 27 watt, which is a die limit that no TO220 survives for long.
That curve is why a 750 milliohm part at 800 V is a half amp device and a 270 milliohm part at 900 V is a two amp device. The resistance is the loss, and the loss is the current squared. Choosing between them is a question of the current the converter actually delivers, and a part that is oversized for the current is not safer, it is just larger and slower.
The gate charge at 800 V also matters even at low current, because the switching loss depends on voltage, charge and frequency rather than on current. A converter that runs at 100 kHz with 30 nC of gate charge at 400 V spends about 1.2 watt per transition pair, which is more than the conduction loss at 1 A. That is the balance an offline switch has to be chosen around.
The TO220 tab at 800 V
The tab is the drain and it sits at the full rectified mains potential plus the flyback spike. A bolted joint to an earthed heatsink needs a thermal pad rated for the voltage, and the pad's thickness and the mounting hardware determine the creepage. This is the part of the assembly that a safety review looks at first, and it is not a detail that can be settled after the board is built.
The through hole leads also carry the high voltage close to the board surface, and at 800 V with any flux residue or humidity the surface tracking path matters. Conformal coating on the high voltage side, or a slot between the drain and the gate traces, are the normal protections.
Thermally, a TO220 with a clip on sink and a 5 degree per watt sink handles 3 watt with a junction about 60 degrees above ambient, which is fine. The same part with no sink at all handles about 1 watt, which is the 0.5 A operating point.
Holding a long life part in supply
Offline switches at 800 V with a small current tend to stay in a product for a decade, and the parts that serve that market are the ones that reach end of life first, because the volumes are low. Our last time buy and LTB planning page covers how a buffer is sized and recorded when a part like this goes on a final order notice.
The alternative to a last time buy is a substitute, and at this voltage the substitute has to match the package, the gate charge and the body diode. A part with a different tab or a different creepage is a board change, and a board change on a certified supply is a re-qualification.
The sourcing side of this part is covered on the material requirements planning. For a low volume offline switch, that page covers how a build plan is turned into a purchase plan.
Questions we get on this code
Is 6 A the working current? No. At 750 milliohm the continuous current is about 1 A with a small heatsink and 0.5 A without one.
Is 800 V enough for a 400 V bus? Yes with margin for a surge. A 650 V part on the same bus has almost no margin, which is why 800 V parts exist in this cell.
Can the tab be earthed directly? Only with an insulating pad rated for the voltage. Without one the heatsink is live at the drain potential.
How is it packed? TO220 normally ships in tubes with a fixed count. We confirm the tube count and the date code on the quotation.