HX25400F
Product Specifications
HX25400F
Hisiwell — Discrete & Power Semiconductors
Product Overview
The HX25400F from Hisiwell is a discrete power semiconductor delivering efficient switching and power conversion. Hisiwell is a recognized semiconductor supplier providing reliable components for global electronics manufacturing.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- Low Rds(on) for minimal conduction losses in power switching
- Fast switching speed with low gate charge for high-frequency operation
- Avalanche-rated for robust operation under inductive load conditions
- High junction temperature rating for demanding environments
- Logic-level gate drive compatible for simplified design
- RoHS and AEC-Q101 qualified options available
Key Specifications
| Vds / Vce | V |
| Id / Ic | A |
| Rds(on) / Vce(sat) | mΩ |
| Qg | nC |
| Technology | — |
| Package | — |
| Configuration | — |
| Mounting | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HX25400F: a 400 W index row with a 240 W parameter list underneath it
The HX25400F is a gallium nitride radio frequency power transistor from Hisiwell for the HF to 2500 MHz band, on a 28 or 48 V supply, in a flanged package with what the vendor calls a high performance thermal package. The index row gives it 400 W, 19 dB of gain, 71 per cent drain efficiency and a 48 V rail. The parameter list on the same product page gives it a maximum output above 240 W, a best drain efficiency above 82 per cent and a linear gain above 19.5 dB.
Those two sets do not agree, and the gap is not small: 400 W against 240 W is a factor of 1.67, or 2.22 dB. There is a reading that reconciles them: 400 W is the class label used across the family, and the parameter list describes a measured device at a stated condition. There is also a reading that does not reconcile them at all. The page publishes both and this page reports both, side by side, without choosing.
What can be said without choosing is what each number is good for. The index figure is the one a distributor catalogue will repeat. The parameter list figure is the one that has to hold on a test bench. A quotation that promises 400 W and a purchase order that specifies 240 W are two different transactions, and a buyer should know which one is being signed before the parts ship.
The HX25400F rows, index against parameter list
| Part class | Gallium nitride power transistor, wideband, thermal package, flanged |
| Frequency range, index row | DC to 2.5 GHz |
| Frequency range, product description | HF to 2500 MHz |
| Output, index row | 400 W |
| Output, parameter list | Maximum output power above 240 W |
| Gap between the two, calculated | 160 W, a factor of 1.67, 2.22 dB |
| 400 W in dBm, calculated | 56.02 dBm |
| 240 W in dBm, calculated | 53.80 dBm |
| Gain, index row | 19 dB |
| Gain, parameter list | Linear gain above 19.5 dB |
| Efficiency, index row | 71 per cent |
| Efficiency, parameter list | Best drain efficiency above 82 per cent |
| Supply, index row | 48 V |
| Supply, product description | 28 or 48 V supply mode |
| Package | Flanged, described as a high performance thermal package |
| Thermal resistance, junction to case | Not published on the page |
| Gate bias point and quiescent current | Not published |
| Load impedance table | Not published on the page |
| Applied application list | RF and microwave systems |
| Datasheet link | Placeholder only, not a resolvable file |
| Orderable addendum and packing data | None published |
The parameter list is a single line of three bullet points, which is more than the HXN rows offer and less than a table. It gives a maximum output, a best efficiency and a linear gain, all three as inequalities rather than values. An inequality is the correct form for a preliminary sheet and it is a hard form to work with: above 240 W does not say how far above, and above 82 per cent does not say at which frequency or at what back off.
The rail is the second disagreement. The index says 48 V and the description says 28 or 48 V. That is not a conflict so much as a missing row: the part probably has two operating points and only one is tabulated. A customer who needs 28 V for an existing vehicle or battery system has to treat this part as 28 V capable and unverified at 28 V until a factory answer arrives.
What the two power figures imply on the rail
| Case | DC input, calculated | Drain current at 48 V, calculated | Heat, calculated |
| 400 W at 71 per cent, index pair | 563 W | 11.74 A | 163 W |
| 240 W at 82 per cent, parameter pair | 293 W | 6.10 A | 53 W |
| 240 W at 71 per cent, mixed pair | 338 W | 7.04 A | 98 W |
| 400 W at 82 per cent, mixed pair | 488 W | 10.16 A | 88 W |
| 200 W at 82 per cent, half power | 244 W | 5.08 A | 44 W |
The four corners of this table are the reason the gap matters. Read the index pair together and the part draws 11.74 A and leaves 163 W of heat. Read the parameter pair together and it draws 6.10 A and leaves 53 W. Those are not two descriptions of the same operating point, they are two different amplifiers, and the power supply, the choke, the trace width and the sink all change between them.
The mixed pairs are there to show that neither figure can be borrowed across. A 400 W output at 82 per cent is a different device from a 400 W output at 71 per cent, and the 71 per cent is the index figure that sits beside the 400 W. The honest method is to pair the figures that came from the same source and treat the other pair as the risk case.
The difference in heat, 163 W against 53 W, is the one that decides the mechanical build. A 163 W flange needs a cold plate or a heat pipe and a mounting torque procedure. A 53 W flange on a spreader with forced air is a different product. On this part the answer is not known from the page, and the page is what the page is.
Against the rest of the 2.5 GHz shelf
| HX25400F | 400 W index, 240 W parameter | 19 dB gain | 71 per cent index, 82 per cent parameter | 48 V index, 28 or 48 V description |
| HX25600F | 600 W index, 320 W parameter | 17 dB gain | 69 per cent index, 79 per cent parameter | 28 or 48 V, full data sheet |
| HXN50126 | 240 W | Not published | Not published | 50 V, internally prematched |
| HXN50127 | 280 W | Not published | Not published | 50 V, internally prematched |
| HX27240F | 240 W on 1.8 to 2.7 GHz | 18 dB | 80 per cent | 48 V, narrower band |
| HX30370P | 370 W on 2 to 3 GHz | 18 dB | 78 per cent | 48 V, flangeless body |
The HX25600F comparison is the cleanest on the shelf because that part has a real data sheet. Its index says 600 W and its parameter list says above 320 W, a factor of 1.88, so the same pattern repeats one row up. On the HX25600F the data sheet then settles the question with a per frequency table and a thermal resistance, and the fact that the stronger row is the one with the complete document is worth noting when a quotation has to be defended.
Against the HXN rows, the HX25400F is the part with published gain and efficiency, which is the whole difference. A customer choosing between 240 W at an unpublished gain and 240 W at 19.5 dB has a much easier decision than the index wattages suggest, because one of the two can be built against today and the other cannot.
The wider family view is on the RF power transistor cross reference. Where a buyer needs the vendor documents reconciled before a purchase order, RF component sourcing covers what is requested and what comes back.
What has to be settled before this part is quoted
Three questions belong in the first message to the factory on this part: which output figure is the orderable one, whether the 28 V rail is a rated operating point or a mention, and what the load impedance is at the frequency of use. None of the three is answered on the public page, and each of them changes the quotation by more than the price usually moves.
No orderable addendum, packing column, marking code or moisture level is published, and this page quotes none of them. The purchase order should carry the part number, the rail, the band, the mode, the output point and the quantity. The flanged body is stated, so the mechanical drawing is a legitimate request with the first order and not a favour.
Lead time is unpublished. On a flanged high power part the variables are the flange stock, the die attach and the test, and a schedule quoted without those is a placeholder. That is the honest state, and a buyer planning a build around a firm date should get the date in writing.
For a second source at this band and rail, the qualification path is on the one stop RF supply page, which covers the measurements that have to be repeated after a substitution.
Questions buyers ask about the HX25400F
Is it a 400 W part or a 240 W part? The index says 400 W and the parameter list on the same page says above 240 W. Both are published. Until the factory answers, 240 W is the figure that can be defended and 400 W is the figure to question.
Does the 82 per cent efficiency apply at 2.5 GHz? The parameter list gives a best figure and no condition. Best efficiency is normally at the low end of the band on a wideband part, so the 2.5 GHz number is likely lower. Ask for the sweep.
Is there a data sheet? The product page has a data sheet link that resolves to a placeholder rather than a file. A real document has to be requested, and the part number on the label should be checked against it.
Can it be used at 28 V? The description says 28 or 48 V supply mode and the index says 48 V. Nothing published separates the two operating points. Treat 28 V as unverified until the factory confirms the bias point and the output at that rail.
Where a comparison has to be made across shelves on one line, the reference page is the cross reference.