Contact Us

LTM8027EY#PBF

Brand: Analog Devices
Analog Devices LTM8027EY#PBF is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTM8027EY#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTM8027EY#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTM8027EY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTM8027EY#PBF: the BGA body, a 42 V automotive bus and the 24 V ceiling

The LTM8027EY#PBF is the same 60 V, 4 A module in the 15 mm by 15 mm by 4.92 mm ball grid array, with SAC305 balls under finish code e1 and an MSL 3 rating. Input range is 4.5 V to 60 V with a 7.5 V start floor, output range is 2.5 V to 24 V, and the output is set by one resistor to ground on the ADJ pin, which the module regulates to 1.23 V. The E grade covers -40 C to 125 C at the junction, the same window as the I grade in this family.

Published values

ParameterValue
Input voltage4.5 V to 60 V, 7.5 V minimum to start
Output settingRADJ = 613.77 / (VOUT - 1.23), in kohm
Output current4 A DC, quoted at 60 V in and 12 V out
Switching frequency100 kHz to 500 kHz, RT sets it
Package15 mm x 15 mm x 4.92 mm BGA, SAC305 balls, MSL 3
Junction to ambient12.2 C/W, 9.3 C/W to case top
Bias pinsBIAS1 above 8.5 V shuts the internal regulator down
Shutdown current9 uA into VIN
Temperature range-40 C to 125 C, E grade
Synchronisationexternal clock 100 kHz to 500 kHz on SYNC

A 42 V bus and a 60 V rating are two different questions

A 42 V automotive bus sits inside the 60 V rating with 18 V of headroom for a load dump, and that is the easy half. The number that decides whether the rail comes up at all is the start floor: the module needs 7.5 V on VIN to start, so a cold crank event that pulls the bus to 6 V will not start it, whatever the input capacitor is sized at. Once running, holding BIAS1 above 6.5 V from an external source lets it keep regulating with VIN as low as 4.5 V, which is the arrangement to quote for a start-stop vehicle.

At 42 V in and 24 V out the duty cycle is 57 percent, so on time is not the problem and loss is. 24 V at 4 A is 96 W out and about 8.35 W in the package at 92 percent, which on 12.2 C/W is a 102 C rise and about 23 C of ambient headroom. A 42 V to 24 V rail at full current is a heat-sink or airflow decision before it is a component decision.

Balls against pads, and what changes on the board

The die, the inductor and the controller inside the BGA and the LGA are the same, so the electrical section of the data sheet is common to both bodies and 12.2 C/W junction to ambient is quoted for each. What changes is the interconnect and the height: SAC305 balls on 1.27 mm pitch against Au pads, and 4.92 mm of body against 4.32 mm, which matters on the underside of a board where a 0.6 mm difference decides whether a shield can fits.

MSL 3 is 168 hours of floor life out of the sealed bag at 30 C and 60 percent relative humidity, and it applies to both bodies. A build that reflows the module on the top side and then runs the board through a second pass for the underside spends that budget twice, so the tray should stay sealed until the pass that carries the module is scheduled, and a partial reel should be baked rather than left on the line.

E grade, I grade and what an order code actually buys

LTM8027EV, LTM8027IV, LTM8027EY and LTM8027IY are all -40 C to 125 C. The MP codes are -55 C to 125 C. For a 42 V automotive board the E grade is the normal choice, and paying for the I grade buys a label rather than a wider window. What does change with the suffix is the pad finish, and that is a process decision, not a temperature one.

The family has been in the catalogue long enough that the usual alternative offered when the 8027 is on allocation is the LTM8026, which is 36 V in and 11.25 mm by 15 mm. The two are not pin compatible, so a substitution is a board change and not a socket swap, and any cross reference has to start from the footprint and the input rating rather than from the current rating alone.

For a board that has to keep running while a reel runs out, the power management cross reference is where the family alternatives sit, the pin to pin cross reference is the check list before a substitute goes in, and how to verify a drop in replacement is how a gap is covered without a new line item.

Two questions buyers ask

Can the module run from a 42 V rail with load dump transients above 60 V? No. 60 V is the rating, not a transient allowance, so a clamp or a surge stopper has to sit in front of the module on an automotive bus. The 4.5 V to 60 V range is the operating window, and 7.5 V is needed to start.

Is the BGA a drop-in for the LGA? No. The ball pattern, the standoff and the reflow profile differ, and the height moves from 4.32 mm to 4.92 mm. The electrical behaviour is the same, so the substitution is a board revision rather than a component swap.