LTC6957HMS-2#PBF
Product Specifications
LTC6957HMS-2#PBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTC6957HMS-2#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LTC6957HMS-2#PBF: The 45 fs Jitter Figure Belongs to a Different Member of the Family
The LTC6957 family is four parts that share one die and differ in output logic: the -1 is LVPECL, the -2 is LVDS, the -3 is CMOS with in-phase outputs and the -4 is CMOS with complementary outputs. The headline additive jitter of 45 fs rms is quoted for the LTC6957-1. A board that specified the -2 code because the receiving PLL wants LVDS, and then wrote 45 fs into a jitter budget, is carrying a number that belongs to the LVPECL member. The HMS suffix in this order code is the 12-lead MSOP body, not a grade.
What the part actually does
It takes a sine wave, or any logic signal up to 2 V peak to peak, and turns it into a low jitter logic output. The input stage has selectable lowpass filtering on the FILTA and FILTB pins, and the point of that filtering is not bandwidth but slew: a 10 MHz reference sine wave arriving at a few hundred millivolts rms is slow, and amplifying it with noise produces jitter at the zero crossings. Filtering the input before the last gain stage removes the noise that the slow edges would otherwise convert into timing error. The frequency range is quoted to 300 MHz, with a supply of 3.15 V to 3.45 V and operation specified from minus 40 C to plus 125 C.
| Member | Output logic | Typical use |
|---|---|---|
| LTC6957-1 | LVPECL | Clock distribution where the lowest additive jitter is wanted |
| LTC6957-2 | LVDS | Differential link into an ADC, DAC or DDS clock input |
| LTC6957-3 | CMOS, in phase | Two single ended clocks that must be aligned |
| LTC6957-4 | CMOS, complementary | A differential pair built from single ended drivers |
Timing numbers that matter to a converter clock
Propagation delay for the LVDS member is quoted as 0.65 ns typical and 1.15 ns maximum, with an output skew of 3 ps typical and a delay variation of 0.1 ps per degree C over temperature and about 50 ps per volt of supply. For a single converter those are small. For a two converter board running from the same reference, the skew and not the jitter is what breaks the channel matching, and 3 ps at 100 MHz is 0.1 degree of phase. The output current limit for the LVDS member is 10 mA, which is why a 100 ohm termination at the receiving end is not optional.
When the sine wave is the wrong input
This part exists to make a sine wave into logic, and it does that better than it makes logic into logic. Feeding it a CMOS clock that already has fast edges gains nothing and adds the input filter as a delay. Feeding it a clipped or distorted sine wave, on the other hand, keeps the zero crossing information but adds harmonics that the filter cannot remove, so the source should be a clean oscillator and not a squared up version of one. In a chain of reference, buffer and converter, the buffer should be the last thing before the clock pin, with the termination at the pin and not at the buffer.
Choosing the replacement in a shortage
A shortage on the -2 code is not solved by fitting the -3, because CMOS outputs cannot drive an LVDS termination and the receiver will see half the swing. The pin compatible question here is the output type first and the package second. The pin to pin cross reference page covers the package field, the obsolete RF part replacement page covers the case where the family is being phased out, and lot verification follows the incoming inspection plan.