Contact Us

LT3958EUHE#PBF

Brand: Analog Devices
Analog Devices LT3958EUHE#PBF is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LT3958EUHE#PBF — Analog & Mixed-Signal ICs | Superb Automation

LT3958EUHE#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LT3958EUHE#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LT3958EUHE: An 84 V Switch on a 5 V Input Cannot Reach 80 V at 1 MHz

The LT3958 is a current mode converter with an internal 3.3 A, 84 V switch, a 5 V to 80 V input range and a 100 kHz to 1 MHz programmable frequency, able to run as a boost, a flyback, a SEPIC or an inverting converter from the same pins. The two numbers that decide whether a given application works are the minimum off time of 200 ns typical and 275 ns maximum, and the minimum on time of 250 ns typical and 300 ns maximum. Together they cap the duty cycle at each end, and a boost ratio is a duty cycle requirement in disguise.

The duty cycle arithmetic

At 1 MHz a period is 1000 ns, and 200 ns of minimum off time is 20 percent of it, so the maximum duty is 80 percent. A boost from 5 V to 80 V needs 93.75 percent, which is 62.5 ns of off time at 1 MHz, three times below the limit. Dropping to 300 kHz gives a 3.33 us period, so 200 ns of off time is 6 percent and the maximum duty is 94 percent, which is enough for the 16 to 1 ratio with a little room. The shortest on time caps the other end: at 300 kHz, 250 ns is 7.5 percent duty, so a converter running near 20 to 1 step up is at the limit and one running at 40 to 1 is over it.

The switch current is an input current

3.3 A flows in the switch, and in a boost the switch carries the input current, so the output current is that input current times the ratio and the efficiency. From 12 V to 48 V at 85 percent efficiency the input current for 1 A of output is about 4.7 A, which is already above the switch rating; the same converter delivers about 0.6 A of output at the limit. Buyers who read 3.3 A as an output current size the load wrongly, and the inductor saturation and the sense resistor are then specified against a current the part never sees.

ItemPublished valueWhat it decides
Input range5 V to 80 VCold crank to 48 V telecom
Switch3.3 A, 84 VInput current in a boost
Minimum off time200 ns typical, 275 ns maximumCaps duty at 80 percent at 1 MHz
Minimum on time250 ns typical, 300 ns maximumFloor for a small duty ratio
Internal regulator7.2 V, 19 to 29 mA at 80 VGate drive budget at high input

Quiescent current and the internal regulator

The part draws 1.6 mA typical and 2.2 mA maximum while switching, and only 350 uA typical when the internal low dropout regulator is disabled and the gate drive is supplied from an external 7.5 V rail. Shutdown current is below 1 uA. The 7.2 V internal regulator can deliver 19 to 29 mA at an 80 V input, which is the gate charge budget, and a large FET or a high frequency makes that budget tight enough to justify the external rail.

Feedback and the negative output case

The FBX pin regulates to 1.600 V when the feedback voltage is positive and to minus 0.800 V when it is negative, which is how the same part serves a positive boost and an inverting converter without an external inverter. The overvoltage lockout is 6 to 10 percent above the set point on a positive output and 7 to 14 percent on a negative one, so a load dump transient that pushes through the inductor trips the switch before the output capacitor sees it.

Thermals in the 5 by 6 mm package

The 36 lead QFN is rated 43 C per watt junction to ambient and 5 C per watt junction to case, and the switch on voltage is 180 mV at 2 A, which is about 0.09 ohm and 0.98 W at the 3.3 A limit. A 48 V to 5 V application at 1 A output loses more in the switch than the junction rise from 43 C per watt suggests only if the board copper is adequate; the exposed pad is the whole thermal path.

Where it is the right part

Industrial 24 V and telecom 48 V rails that need a floating or negative output are the natural home, and the power management cross reference page lists the converters that share this footprint, the component lead time solutions page covers grade and package substitution, and lot checks follow the incoming inspection plan.