LTM4643IY#PBF
Product Specifications
LTM4643IY#PBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTM4643IY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LTM4643IY#PBF: The BGA Ultrathin Quad Module at 2.42 mm
The LTM4643IY#PBF is the I grade BGA version of the quad 3 A module: 4 V to 20 V in, 0.6 V to 3.3 V out, 3 A per channel with 12 A available from a paralleled array, plus or minus 1.5 percent total DC error, in a 9 mm by 15 mm by 2.42 mm BGA with SAC305 balls, 0.83 g, MSL 3. The I grade is guaranteed over -40 C to 125 C internal. The BGA is 0.6 mm taller than the LGA version of the same part, and for that 0.6 mm it buys balls that self centre during reflow and a package that tolerates a coarser paste print.
Published values
| Parameter | Value |
|---|---|
| Input range | 4 V to 20 V, 2.375 V to 20 V with an external bias |
| Output range | 0.6 V to 3.3 V per channel |
| Output current | 3 A per channel, 12 A as an array |
| Total DC error | plus or minus 1.5 percent, 1.477 V to 1.523 V at 1.5 V |
| Current limit | 3.5 A minimum, 5 A typical per channel |
| Bias current | 6 mA switching, 2 mA with MODE low, 11 uA shutdown |
| Switching frequency | 1.2 MHz default, external sync through CLKIN |
| Minimum on and off time | 40 ns on, 70 ns off |
| Load step | 160 mV deviation, 40 us settle |
| Thermal | 10 C/W junction to ambient, 2.75 C/W junction to case bottom |
| Package | 9 mm x 15 mm x 2.42 mm BGA, 77 balls, SAC305, 0.83 g, MSL 3 |
| Temperature | I grade guaranteed -40 C to 125 C internal |
Balls against lands on a 2.42 mm module
The LGA version of this part is 1.82 mm and 0.70 g, and it needs a land pattern with a paste print that holds its shape. The BGA is 2.42 mm and 0.83 g and self centres on its balls during reflow, which tolerates a placement offset of a few tenths of a millimetre that the LGA would not. On a dense board where the module sits next to tall parts and the stencil aperture is shared, the BGA is often the assembly decision rather than the electrical one.
The cost is inspection. Balls under a 2.42 mm package are not visible from the side, so voiding and collapse have to be checked by x-ray, and a rework needs a dedicated nozzle. Both packages are MSL 3 with a 260 C peak body rating, so the reflow profile does not change.
Twenty volts in, 3 amps out, four times
The 20 V input is what makes this family useful on a 12 V or 18 V bus without an intermediate converter, and the 3.3 V output ceiling is what keeps it out of 5 V applications. Four channels at 1.5 V and 3 A is 18 W, drawing about 1.8 A from a 12 V bus at the published 0.45 A per channel. That is an 83 percent terminal efficiency, and the loss, about 3.1 W, is spread across a 135 square mm package.
The 40 ns minimum on time is the binding constraint at the low output end: 0.6 V from 20 V is 3 percent duty, which needs the frequency below about 750 kHz. From 12 V the same rail is 42 ns at the default 1.2 MHz and fits without any change.
The array and the four independent rails
Two channels parallel give 6 A, four give 12 A, and the phase relationship is set on PHMODE. Each channel keeps its own input capacitor and its own feedback divider, and the outputs are tied at the load. For an FPGA with four rails the array is not used at all: 0.9 V, 1 V, 1.2 V and 1.5 V at 3 A each is the documented application, and the only external parts are four set resistors, four soft start capacitors and the ceramics.
The current limit is 3.5 A minimum against a 3 A rating, so a load that steps hard will approach it. The 5 A typical maximum is the fault current, and the inductor inside the module is rated for it, but the trace and the connector on the output are not necessarily.
Sourcing and the grade
The code reads as family, I grade, Y for BGA, #PBF for RoHS with SAC305 balls. The E grade has a 0 C guarantee, the MP grade -55 C, and the SnPb finish drops the #PBF. Because all grades share the 77 ball package, a board qualified on the I grade accepts the E or MP code without a change, which is what makes this family easy to keep supplied during an allocation.
The parts that are not interchangeable are the LGA and the BGA. They differ in height by 0.6 mm and in footprint entirely, so the package decision is made once, at the board, and the grades are then a purchasing choice.
The pages that answer this most often are how to verify a drop in replacement for the family alternatives, OEM procurement for the acceptance test, and component lead time solutions for the case where a replacement has to be fitted before the next build.
Two questions buyers ask
Can the BGA version replace the LGA version on an existing board? No. The footprints are different, the heights differ by 0.6 mm, and the ball field is not the land pattern. They share the family and the electrical specifications, not the board.
What is the thermal path for a 2.42 mm module? The junction to case bottom figure is 2.75 C/W and junction to ambient is 10 C/W, so the lands are still the main path even at 2.42 mm. Copper under the ball field and a ground plane on the next layer are what the number depends on.