LTM4657EY#PBF
Product Specifications
LTM4657EY#PBF
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The LTM4657EY#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LTM4657EY#PBF: the E grade of the 8 A module, and the four numbers that decide a substitution
The LTM4657EY#PBF is the E grade of the 8 A, 20 V input module in the 6.25 mm by 6.25 mm by 3.87 mm ball grid array, with the same 0.5 V to 5.5 V output range, the same plus or minus 1.5 percent dc error and the same pin compatibility with the 12 A LTM4626 and the 15 A LTM4638. On this part the E and I order codes are both listed at minus 40 degree C to 125 degree C, so the suffix is a guarantee and test decision. A substitution between the two, or to a larger member of the family, comes down to four numbers.
Published values
| Parameter | Value |
|---|---|
| Input voltage | 3.1 V to 20 V |
| Output voltage | 0.5 V to 5.5 V |
| Output current | 8 A dc |
| DC output error | plus or minus 1.5 percent |
| Pin compatible parts | LTM4626 at 12 A, LTM4638 at 15 A |
| Thermal resistance | 17 degree C per W |
| E grade range | minus 40 degree C to 125 degree C |
| I grade range | minus 40 degree C to 125 degree C |
| Package | BGA, 6.25 mm x 6.25 mm x 3.87 mm |
| Weight | 497 mg |
| Modes | continuous or selectable discontinuous |
| Tracking | output voltage tracking for sequencing |
The four numbers: current, loss, copper and height
A substitution across this family changes four things. The current rating goes from 8 to 12 or 15 A, the loss at a given load stays roughly the same per amp, the copper needed under the module rises with the current, and the height changes with the inductor inside. The 3.87 mm height of the 8 A part is not the same as the taller members of the family, so a board with a low profile constraint cannot always take the larger part even though the balls line up.
Working the numbers: 8 A at 1 V is 8 W out and about 1.4 W of loss at 85 percent, giving a 24 degree C rise at 17 degree C per W. The same 1 V rail at 15 A is 15 W out and 2.4 W of loss, a 41 degree C rise in the same footprint. That is inside the 125 degree C junction at a 70 degree C ambient and outside it at 85, so the headroom a substitution appears to buy is smaller than the current ratio suggests.
Why 1.5 percent of a 0.5 V rail is 7.5 mV and why that is the whole budget
Half a volt at plus or minus 1.5 percent is plus or minus 7.5 mV, and a 1 milliohm ground return carrying 8 A drops 8 mV. Without the differential sense amplifier the return drop alone uses the entire dc error budget, which is why the part has one and why the sense lines have to be taken to the load rather than to the nearest via. On a 5 V output the same 1.5 percent is 75 mV and the return drop is a tenth of it, so the sense lines matter far more on the low voltage rails.
The same arithmetic applies to the reference and the feedback divider tolerance, which are inside the 1.5 percent rather than added to it. A build that adds the divider tolerance on top of the module figure is double counting, and a build that ignores the sense line drop is under counting.
A 20 V input with a 0.5 V output is a duty cycle question
Twenty volts to 0.5 V is 2.5 percent, and to 1 V it is 5 percent. At 1 MHz those are 25 ns and 50 ns of on time, so the low output from the high input is where the switching frequency has to come down. The part will run at 1 MHz on a 5 V to 1 V conversion all day, and the same part on a 20 V to 0.9 V conversion is limited by the minimum controllable pulse rather than by the current rating.
For a buyer, that is the difference between a part that fits and a part that regulates: the efficiency curve at 20 V in and 0.9 V out is short, and a build that needs that combination is usually better served by a two stage conversion or by a module with a lower minimum on time. The data sheet's own application circuits all sit at input voltages where the duty cycle is comfortable.
Buyers usually arrive at the power management cross reference to find the family alternatives, then use the pin to pin cross reference to confirm a substitute before it is fitted; how to verify a drop in replacement is the routine for a part that has already stopped shipping.
Two questions buyers ask
Does the E grade differ from the I grade in any electrical way? Both are listed at minus 40 degree C to 125 degree C with the same body, weight and ballout, so the differences are the guarantee, the part marking and the finish code. A substitution between them is a documentation change rather than a board change, and the thermal case is identical.
Can the module be used without the input capacitor the data sheet shows? The module needs the bulk input capacitance because the switching current has to come from somewhere local. The data sheet's typical application shows a 10 uF plus a 0.1 uF at the input, and a build that feeds the module through a long trace without them sees the trace inductance in series with the switch, which shows up as ringing at the input pins and as conducted emissions.
Tracking a rail up behind another one
The module has an output voltage tracking pin, so its output can be made to follow another rail during start-up rather than ramping from zero on its own soft start. That is what a memory rail or an analog rail needs when the load has a defined power sequence and the two rails must not cross.
The tracking pin is a low current input with its own internal pull down, so the master rail is loaded by a resistor divider rather than by the pin itself. A divider that is too high in value leaves the tracking pin below its threshold at the top of the ramp and the rail stops short of regulation, which is the most common tracking fault on this family: the rail looks correct at 25 degree C and drops a few percent at temperature because the divider current fell with the leakage on the pin.