ADR5043BRTZ-REEL7
Product Specifications
ADR5043BRTZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADR5043BRTZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADR5043BRTZ-REEL7: The B Grade Is 0.2 Percent and 100 ppm, and a Shunt Reference Needs a Resistor
The ADR5043 is the 3.000 V member of a five part shunt reference family in SC70 and SOT-23 bodies. The RT suffix in this code is the SOT-23 package, and the B grade is 0.2 percent of initial accuracy with a 100 ppm per degree C drift, against 0.1 percent and 75 ppm for the A grade. Two facts follow that a bill of materials rarely records. First, the headline 0.1 percent and 75 ppm on the front page belong to the A grade, so a B grade code bought against that headline is outside the accuracy the buyer thought he was getting. Second, a shunt reference has no ground pin to sink current into: it regulates by conducting, so a bias resistor has to be sized for the whole operating window.
Sizing the bias resistor is the real work
The operating current window is 50 uA to 15 mA. The resistor has to pass at least 50 uA plus the load at the lowest supply voltage, and must not pass more than 15 mA plus the load at the highest, and it has to do that over the full temperature range of the resistor itself. On a 5 V rail with a 3.0 V reference and a 100 uA load, a 10 kohm resistor passes 200 uA at nominal and 190 uA at 4.75 V, so the reference has 90 uA of margin at the low rail and the resistor dissipates 0.4 mW. On a 3.3 V rail the same reference has only 300 mV of headroom at nominal, which is 30 uA through 10 kohm: below the 50 uA minimum, so the reference is not in regulation at all.
| Rail | Headroom to 3.0 V | Resistor for 200 uA at nominal | Current at minus 5 percent |
|---|---|---|---|
| 5.0 V | 2.0 V | 10 kohm | 190 uA |
| 3.6 V | 0.6 V | 3.0 kohm | 180 uA |
| 3.3 V | 0.3 V | 1.5 kohm | 180 uA |
| 3.3 V at minus 5 percent | 0.135 V | 1.5 kohm gives 90 uA | 90 uA, still above the 50 uA floor |
Drift, and where a shunt part still wins
100 ppm per degree C across the 165 C industrial span is 1.65 percent, or 49.5 mV on 3.0 V. That is not a precision reference in the sense a 16-bit converter needs, since a 16-bit step on 3 V is 46 uV and the drift is a thousand steps. What it is good at is a compact, always biased reference for a comparator threshold, a 12-bit converter, or a circuit that is trimmed at the temperature it runs at. The family is stable with any capacitive load and does not need an output capacitor, which is the opposite of most series references and a real saving in a 2 mm by 2 mm footprint.
Two pin compatible families and one trap
The pins are compatible with the LM4040 and LM4050 shunt references, which makes this a drop in for circuits already built around those parts, and the 50 uA minimum is lower than several of them, so the bias resistor can usually stay. The trap is the third pin: the data sheet recommends connecting it to the positive rail rather than leaving it floating, and a board that leaves it open on one revision and ties it on the next will behave differently at the same current. Automotive qualified W versions exist in the same family, and the qualification is carried by the W in the order code, not by the package.
Buying a shunt reference by grade
Because the grade is a suffix, the accuracy and the drift both move with the order code, and a customer asking for the A grade performance at the B grade price is asking for a different part. The ADC DAC cross reference page covers the converter pairing, the ADI part second source page covers the grade question, and lot checks follow the incoming inspection plan.