Contact Us

AD8319ACPZ-R7

Brand: Analog Devices
Analog Devices AD8319ACPZ-R7 is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8319ACPZ-R7 — Analog & Mixed-Signal ICs | Superb Automation

AD8319ACPZ-R7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8319ACPZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8319ACPZ-R7: The Output Rail Is Not the Limit, the 45 dB Accuracy Window Is

The AD8319 is a demodulating logarithmic detector that converts an RF input from 1 MHz to 10 GHz into a decibel scaled voltage, with a slope of minus 22 mV per dB and an intercept of 15 dBm at 50 ohm. With a 5 V supply the output can swing to about 4.9 V, which at 22 mV per dB would be 222 dB of range if the output rail were the only limit. It is not: the specified dynamic range is 45 dB with less than 3 dB of error, and the part is accurate to 1 dB over temperature within that window. Everything outside the window still moves the output, which is useful for detecting presence and useless for measuring level.

Where the 45 dB window sits

With an intercept of 15 dBm and a slope of minus 22 mV per dB, an input at 15 dBm drives the output to 0 V and an input at minus 30 dBm drives it to 0.99 V. The 45 dB window therefore covers roughly minus 30 dBm to plus 15 dBm, and the exact placement depends on the input used and on the temperature adjustment resistor. A receiver that needs to measure down to minus 60 dBm is 30 dB below the window and needs either a coupler with more coupling or a different detector; no amount of output range fixes it.

Input at 50 ohmOutput, nominal slopeStatus
15 dBm0 VTop of the window, at the intercept
0 dBm0.33 VInside the specified window
Minus 15 dBm0.66 VInside the specified window
Minus 30 dBm0.99 VBottom of the window
Minus 45 dBm1.32 VOutside the accuracy window, presence only

Response time and pulse behaviour

The fall and rise times are quoted as 6 ns and 10 ns, which is what allows the part to follow an RF burst at a pulse rate beyond 50 MHz. That speed comes from the detector cells and the output filter capacitor on the CLPF pin, and the capacitor is the trade the user makes: a larger capacitor smooths the output and slows the response. For a radar or a TDD radio the burst envelope has to be resolved, so the capacitor is chosen against the shortest burst in the protocol rather than against the best ripple figure. The asymmetry between the 6 ns fall and the 10 ns rise is real and shows up as a pulse width error in a burst detector.

Measurement mode and controller mode

As a measurement device the output is fed to an ADC and converted with the slope and intercept. As a controller the output is tied back to the setpoint input, and the loop then drives a power amplifier so that the detector output equals the setpoint, which is a level control loop with no firmware in it. The controller connection is the reason the part is used in transmitter chains: it closes the loop on actual delivered power rather than on a DAC setting, so supply and temperature drift are absorbed. The supply current is 22 mA from 3.0 V to 5.5 V, and the body is 2 mm by 3 mm, which is small enough to sit next to the coupler.

Buying a detector with a defined window

Two detectors with the same headline range can have different intercepts, so the part number swap has to match slope, intercept and window and not only the frequency range. The RF component sourcing page covers the detector class, the how to choose an RF amplifier page covers the amplifier the loop drives, and the incoming inspection plan page covers lot checks.