ADN4691EBRZ
Product Specifications
ADN4691EBRZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADN4691EBRZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADN4691E: M-LVDS at 200 Mbps Over a Bus That Carries Thirty Loads
The ADN4691E is a 3.3 V multipoint low voltage differential signaling transceiver, half duplex, in an 8-lead SOIC. It switches at 200 Mbps, which is 100 MHz, drives bus loads between 30 and 55 ohms, and conforms to the TIA/EIA-899 M-LVDS standard. Its receiver is the type 1 variety with 25 mV of hysteresis, as opposed to the type 2 parts in the same family that use a 100 mV threshold offset for open circuit and bus idle fail-safe. The common mode range of minus 1 V to plus 3.4 V allows communication with 2 V of ground difference between nodes, and the bus pins carry 15 kV of ESD protection in the human body model at air discharge.
Why multipoint needs a different physical layer
RS-485 is a multipoint standard and it works, but its driver is built for a bus that can be long and its receivers tolerate a wide common mode at the cost of speed. M-LVDS keeps the differential pair and changes the driver so that it can drive a terminated bus with up to 32 nodes at 200 Mbps, with controlled output transition times so the reflections settle inside a bit. The 30 to 55 ohm load range is the electrical consequence: a backplane with many connectors and stubs presents a load that a point to point LVDS driver cannot handle. On a shelf of cards that all need to see the same clock and the same control traffic, this is the part that does it without a hub.
Values at a glance
| Parameter | Value | Note |
|---|---|---|
| Standard | TIA/EIA-899 M-LVDS | Multipoint, not point to point LVDS |
| Data rate | 200 Mbps, 100 MHz | With controlled output transition times |
| Bus load | 30 ohms to 55 ohms | Terminated backplane with multiple cards |
| Receiver type | Type 1, 25 mV hysteresis | Type 2 parts use a 100 mV offset for fail-safe |
| Common mode | Minus 1 V to plus 3.4 V | 2 V of ground difference between nodes |
| ESD | 15 kV HBM air, 8 kV HBM contact | Plus 10 kV IEC 61000-4-2 air discharge |
| Bus behaviour | Driver outputs high impedance when disabled or unpowered | Glitch free power up and power down |
| Package, temperature | 8-lead SOIC, minus 40 C to plus 85 C | Full duplex members are 14-lead |
Type 1 against type 2 is a system decision
A type 1 receiver with 25 mV of hysteresis resolves small differential signals and needs the bus to be actively driven or terminated to a defined state. A type 2 receiver with a 100 mV threshold offset reads a definite level when the bus is idle or open, which matters on a backplane where cards are hot swapped and the bus can be left floating for a moment. Choosing between them is not a preference: a type 2 part in a system where the differential signal legitimately swings through the offset window will read a false level, and a type 1 part in a hot swap system will chatter when the bus is idle. The family offers both in the same footprint, so the decision belongs to the system specification.
Backplanes, clock distribution and the RS-485 alternative
Backplane and cable multipoint data transmission, multipoint clock distribution and low power high speed links that would otherwise be RS-485 are the three applications the part is specified for. Clock distribution is the one where the electrical detail matters most, because a clock has to arrive with the same delay at every card and a driver that changes its transition time with load will skew it. Controlled transition times and a matched driver are what make the part usable for that. Where the bus is short, the loads are few and the rate is low, RS-485 is still simpler and cheaper, and the honest comparison is against the cost of the extra termination and the lower speed rather than against the transceiver price alone.
Procurement and second source
The M-LVDS family shares a pinout across the half duplex and full duplex members and across the two receiver types, so a substitution is usually possible but changes the fail-safe behaviour. The CAN bus transceiver selection page covers the differential bus parts used alongside it, pin to pin cross reference lists the drops that need no board change, and component lead time solutions covers the 8-lead SOIC when the distributor date is long.