ADR421BRZ
Product Specifications
ADR421BRZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADR421BRZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADR421BRZ: In This Family the B Grade Is the Tighter Drift, Not the Cheaper One
The ADR421 is the 2.500 V member of the ADR420 to ADR425 XFET reference family. Buyers who assume the usual lettering, where the A grade is the best and the B grade is the cost reduced version, get this family backwards: the ordering table in the current revision lists the B code at 3 ppm per degree C over the full temperature range and the A code at 10 ppm, so ADR421BRZ is the part to specify when drift matters. The rest of the front page, 1.75 uV peak to peak of low frequency noise, 50 ppm per 1000 hours of long term stability and 0.5 mA of quiescent current, is common to both grades.
Drift over the span is larger than the initial error
Three ppm per degree C across the minus 40 C to plus 125 C range is 495 ppm, which is 1.24 mV on 2.5 V. A 16-bit converter on that reference has a step of 38 uV, so the drift alone is 32 steps and the reference, not the converter, decides whether the reading holds over temperature. Load regulation of 70 ppm per milliamp adds another 700 ppm at the full 10 mA output, which is 1.75 mV, and line regulation of 35 ppm per volt means a 2 V supply change moves the output by 175 uV. A unit that is trimmed at room temperature and nothing else will see all three terms at once in the chamber.
| Term | Published figure | Error on 2.5 V |
|---|---|---|
| Initial accuracy, B grade | Grade dependent, trimmed at 25 C | Set by the grade field on the order |
| Drift, 3 ppm per degree C | Over 165 C span | 1.24 mV |
| Long term stability | 50 ppm per 1000 hours | 125 uV per 1000 hours |
| Hysteresis | 40 ppm typical | 100 uV after a thermal cycle |
| Load regulation | 70 ppm per mA | 1.75 mV at 10 mA |
| Line regulation | 35 ppm per V | 175 uV for a 2 V change |
Noise and the trim pin
The 0.1 Hz to 10 Hz noise of 1.75 uV peak to peak is 4.6 percent of a 16-bit step on 2.5 V, so low frequency noise is not the limit; it is the reason this part appears in front of 18 and 20 bit converters where the drift is trimmed in firmware instead. The trim pin allows about 0.5 percent of adjustment, which is 12.5 mV, and it needs an external divider to do it. The two pins marked as test points must be left unconnected: they are not spare, and a board that ties them to a plane will fail on the first lot it sees.
Supply headroom and output current
The minimum supply is 4.5 V for the 2.5 V option, so a 5 V rail with 5 percent tolerance leaves 250 mV above the minimum and that is enough. The reference sources 10 mA and sinks little, so a converter that draws its reference current in bursts will modulate the reference unless a small capacitor sits at the pin. The 0.5 mA maximum quiescent current is what makes the family usable in a loop powered transmitter where the whole budget is 4 mA.
Sourcing a precision reference without a grade surprise
The order code carries the grade, so a shortage on the B code cannot be covered by shipping the A code without telling the customer that the drift tripled. The ADC DAC cross reference page covers the converter side of the pairing, the ADI part second source page covers the grade question, and lot checks follow the incoming inspection plan.