Contact Us

LTC1261LIMS8-4.5#PBF

Brand: Analog Devices
Analog Devices LTC1261LIMS8-4.5#PBF is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTC1261LIMS8-4.5#PBF — Analog & Mixed-Signal ICs | Superb Automation

LTC1261LIMS8-4.5#PBF

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTC1261LIMS8-4.5#PBF from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

LTC1261L-4.5: Minus 4.5 V at 20 mA From a 5 V Rail, With Three Capacitors

The LTC1261L-4.5 is a switched capacitor voltage inverter that produces a regulated -4.5 V from a supply of 4.5 V to 5.25 V, with an output current up to 20 mA, output regulation of 4.5 percent, a quiescent current of 650 microamps and 5 microamps in shutdown. It needs three capacitors, a 0.1 microfarad flying capacitor and an input and an output bypass, and it comes in an eight lead MSOP or SO package. An open drain regulator flag pulls low when the output is within 5 percent of its set value, which is the pin that makes it usable as a bias supply rather than a rail.

A charge pump is not an inductor converter

The output current comes through the flying capacitor, which is charged from the input and then inverted onto the output. That means the available current is set by the capacitor value, the switching frequency and the required regulation, not by the input supply's capability. Twenty milliamps is a hard ceiling for this part; a load that draws 25 mA will not be served by a bigger input capacitor or a lower ESR, it will simply fall out of regulation. The 4.5 percent regulation figure applies within that 20 mA window and at the specified capacitor values.

The numbers on the label

ParameterValueNote
Input voltage4.5 V to 5.25 VThe fixed -4.5 V version needs a 5 V class rail
Output voltage-4.5 V fixedThe base part is adjustable from -1.23 V to -5 V
Output currentUp to 20 mASet by the flying capacitor and the switching frequency
Regulation4.5 percentOver the specified load and temperature range
Quiescent current650 microamps, 5 microamps in shutdownSmall enough for a battery instrument
External partsThree capacitors0.1 microfarad flying, input and output bypass
Status flagOpen drain, low when in regulationCan hold a reset line or gate a bias

The 4.5 V input floor is tight on a 5 V rail with tolerance

A 5 V rail with 5 percent tolerance has a minimum of 4.75 V, which is inside the 4.5 V to 5.25 V window and leaves 250 mV of margin. A rail specified as 4.5 V nominal, however, drops to 4.275 V at the bottom of its tolerance and is outside the window, so the inverter will not regulate at the very moment the rest of the board is also struggling. Where the rail is a battery, the part runs out of input range before the battery is empty, which is a specification point rather than a fault.

The regulator flag is the reason to choose this family

A negative rail that is still coming up is worse than no negative rail at all for a gallium arsenide stage, because the gate bias is missing while the drain is present. The open drain flag lets the sequencer hold the drain supply off until the negative rail reports in regulation, and it costs one pin and one pull up resistor. In a bias generator for a field effect transistor amplifier, that is the difference between a reliable power up and a batch of parts that fail on the first switch on.

Sourcing a long life bias part

Parts of this age are usually on a bill of materials that will not be revised, so the practical question is availability in the original package rather than a substitute. The power management cross reference page lists the inverter family, the obsolete part cross reference hub tracks the end of life route, and footprint checks are on the pin to pin cross reference page.