Contact Us

LTC3789EGN#TRPB

Brand: Analog Devices
Analog Devices LTC3789EGN#TRPB is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LTC3789EGN#TRPB — Analog & Mixed-Signal ICs | Superb Automation

LTC3789EGN#TRPB

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The LTC3789EGN#TRPB from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

LTC3789EGN#TRPB: one 12 V rail that survives a 9 V crank and a 24 V jump

The LTC3789EGN#TRPB is a synchronous four switch buck boost controller that holds a regulated output from an input sitting above, below or equal to it. The EGN suffix is the 28-lead SSOP, the narrow package; the same part is also sold in a 4 x 5 mm QFN under a different suffix. One inductor carries the current in every mode, which is the difference between this topology and a SEPIC built around a coupling capacitor.

What the vendor publishes

ParameterValue
Topology4 switch synchronous, single inductor
Input range4 V to 38 V, 40 V maximum
Output range0.8 V to 38 V
Output accuracy1 percent
Switching frequency200 kHz to 600 kHz, phase lockable
Efficiencyup to 98 percent with synchronous rectification
Current limitprogrammable on the input or the output
Internal LDO5.5 V
Power goodwithin 10 percent of set point
Protectiontrue soft start, output short protection in boost mode, no reverse current at start-up
Packages28-lead SSOP, 28-lead 4 x 5 mm QFN

Duty cycle at the two ends of the range

In this topology the transfer is set by the duty cycle of the two switch pairs, VOUT divided by VIN equals D divided by one minus D, so D is VOUT over VIN plus VOUT. At 12 V in and 12 V out the duty is 0.5, all four switches are in the path and the part is in the transition region where its conduction loss is highest. At 4 V in and 38 V out the duty is 0.905, so the low side switch conducts 90 percent of the period, which at 400 kHz is 2.26 microseconds out of 2.5. That long conduction interval is what the inductor, the switch and the gate drive have to survive, and it is where the current limit is reached first.

The 98 percent efficiency figure is a peak, reached in a region where the input sits well away from the output. In the transition region the same board loses two to four points, because both switch pairs are switching and the inductor ripple is at its largest. A system that spends most of its life at VIN close to VOUT should be specified on the transition region numbers, not on the peak.

Where 1 percent and 10 percent land

Output accuracy of 1 percent is 120 mV at 12 V and 240 mV at 24 V, over line, load and temperature. The power good window is 10 percent either side, so at 12 V the flag drops below 10.8 V and above 13.2 V. Between those two numbers sits the useful part of the build: a load that needs the rail inside 1 percent cannot use power good as its only monitor, and a load that tolerates 5 percent has a much easier time with the flag.

Input range of 4 V to 38 V with a 40 V maximum leaves two volts of margin above the operating limit. A 36 V telecom or industrial rail sits close enough that a load dump or a hot plug transient arrives with only 4 V of headroom, so a clamp on the input is not optional. The same 4 V bottom end is what makes the part work on a lead acid battery during crank, provided the inductor and the current limit are sized for the input current at 4 V rather than at 12 V.

Two questions buyers ask

Can the SSOP version be swapped for the QFN on an existing board? No. The two packages have different footprints, different thermal paths and different pin ordering, so a board built for one does not take the other. Choose on the thermal requirement: the QFN has the exposed pad and the lower junction rise, the SSOP is easier to inspect and rework.

Is the input current limit usable as a battery charger? Yes, that is what the second current loop is for. Set the limit below what the source can deliver, and the output voltage loop takes over once the battery reaches its set point. Ask for the sense resistor tolerance and the amplifier offset, because both appear directly in the charge current accuracy.

SUPERB quotes the LTC3789EGN#TRPB against this row and confirms the package suffix before shipment. For a controller that has gone end of life, power management cross reference lists the parameters that have to agree. Pin compatibility questions are answered under pin to pin cross reference, and stock sits in the analog and mixed signal ICs index.

Request Quote — In Stock, 100% New & Original, Full Warranty