ADRF6755ACPZ-R7
Product Specifications
ADRF6755ACPZ-R7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADRF6755ACPZ-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
ADRF6755ACPZ-R7: half a decibel of quadrature error is 40 dB of image rejection
The ADRF6755 puts a quadrature modulator, a fractional N frequency synthesizer with its own voltage controlled oscillator, and a 47 dB digitally controlled attenuator into one package, and covers 100 MHz to 2400 MHz of output. That combination is what a satellite upconverter, a cellular repeater or a broadband radio needs in order to turn a pair of baseband or intermediate frequency signals into a single carrier without building a synthesizer and an attenuator out of separate parts. Frequency resolution is below 1 Hz, the attenuator moves in 1 dB steps, and the whole thing runs from a single 4.75 V to 5.25 V supply.
What the vendor page states
| Parameter | Value |
|---|---|
| Function | I/Q modulator with integrated fractional N synthesizer and oscillator |
| Output range | 100 MHz to 2400 MHz |
| Gain control | 47 dB of attenuation in 1 dB steps |
| Output third order intercept | 20.5 dBm at a 1800 MHz local oscillator |
| Noise floor | minus 161 dBm per hertz at a 1800 MHz local oscillator |
| Baseband bandwidth | 600 MHz at 3 dB |
| Frequency resolution | below 1 Hz |
| Control | SPI or I2C interface |
| Supply | 4.75 V to 5.25 V, a single supply of plus or minus 5 percent |
Image rejection is bought at the board, not in the part
A quadrature modulator suppresses the unwanted sideband only as well as its two baseband paths match. Feed the same signal into both and the image goes away. Half a decibel of amplitude difference and one degree of phase difference between the two paths comes to 39.6 dB of image rejection, which is often not enough for a receiver that has to meet a spurious specification. Two tenths of a decibel and two degrees is 33.6 dB, and half a decibel with five degrees is 25.6 dB. The arithmetic is unforgiving in both directions: the part can be perfect and the board can still give 30 dB. Buyers who are qualifying a first article should measure the image on the actual assembly, not on the evaluation board, because the difference between the two is the length and impedance match of the two baseband traces.
The noise floor translated into a channel
Minus 161 dBm per hertz is minus 101 dBm across a 1 MHz channel and minus 108 dBm across 200 kHz. Those are the numbers to put against the required signal to noise ratio of the standard being built: a system that needs 20 dB of signal to noise in a 200 kHz channel has a floor of minus 88 dBm, and everything above that is headroom for the local oscillator phase noise and the driver. Across the full 600 MHz of baseband bandwidth the same figure integrates to minus 73.2 dBm, which is why the wideband case is never quoted without a channel filter.
47 dB in 1 dB steps as a level plan
Forty seven decibels in 1 dB steps gives 48 settings. One step is 1.16 percent of the voltage, so the attenuator can hold a level within a fraction of a decibel across temperature without touching the modulator. The 20.5 dBm output intercept at a 1800 MHz local oscillator sets how far down the output has to be backed off for a given linearity: a 5 dB backoff costs 10 dB of intercept in the usual third order arithmetic, so a system that needs 35 dBm of intercept cannot get there from this part at any attenuation setting.
Frequency resolution below 1 Hz
Below 1 Hz of resolution at 1800 MHz is 0.0006 ppm, and at 100 MHz it is 0.01 ppm. That is fine enough to place a carrier inside a narrow channel without a second correction loop. The supply window of 4.75 V to 5.25 V is plus or minus 5 percent, which is tighter than a generic 5 V rail is usually held, so the regulator feeding this part belongs in the same review as the modulator. The RF component sourcing page covers the synthesizer and modulator alternatives by band, the lead time page is where to look when the 5 by 5 mm package is on allocation, and the analog and mixed signal category page holds the rest of the RF signal chain parts.
Request Quote — In Stock, 100% New & Original, Full Warranty