MAX22191AUT+T
Product Specifications
MAX22191AUT+T
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The MAX22191AUT+T from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
MAX22191AUT+T: a digital input that steals its own power from the field signal
The MAX22191 is an IEC 61131-2 industrial digital input in a 6 lead SOT23 that takes a 24 V field signal and turns it into either a 3.3 V or 5 V CMOS level or a 2.3 mA current for driving an optocoupler and a status lamp. Its distinguishing feature is that it draws its own operating power from the input signal, so the field side needs no supply rail at all. It accepts anything from minus 60 V to plus 60 V at the input, responds in 250 ns maximum, and is rated from minus 40 C to plus 125 C ambient.
What the vendor page states
| Parameter | Value |
|---|---|
| Standard | IEC 61131-2, Type 1 and Type 3 inputs |
| Input range | minus 60 V to plus 60 V; 48 V operation with external resistors |
| Output | 3.3 V or 5 V CMOS level, or 2.3 mA typical current output |
| Propagation delay | 250 ns maximum |
| Input current limiting | plus or minus 15 percent |
| Quiescent current | 100 microamps typical with an optocoupler |
| Transfer efficiency | 96 percent typical to the optocoupler |
| Diagnostics | CMOS compatible test pulse input |
| Protection | thermal shutdown when the logic supply is present |
| Package and grade | 6 lead SOT23, minus 40 C to plus 125 C ambient |
Two point four milliamps at 24 V is 58 mW, and the part takes all of it
Parasitic power is not free power: the input current that feeds the internal circuits also drops the whole field voltage across the device. At 24 V and 2.4 mA the part dissipates 58 mW, and the same current at 48 V with the external resistors in place dissipates 115 mW, and at 60 V steady state 144 mW. In a 6 lead SOT23 that is the whole thermal story, and it is why the vendor quotes an ambient range rather than a junction temperature alone. A cabinet at 60 C ambient leaves 65 C of headroom to a 125 C junction, which is about 385 C per watt of allowed thermal resistance, a figure a SOT23 on two square millimetres of copper only just meets.
The fifteen percent current window is a system specification
Plus or minus 15 percent around 2.3 mA gives a window from 1.95 mA to 2.64 mA, and that window is what makes the part recognisable to a controller reading the loop current rather than the voltage. In a cabinet where eight inputs share one field supply, the total is 19.2 mA, which is inside the budget of any 24 V supply but adds up quickly across 64 inputs to 154 mA. The 96 percent transfer efficiency means 2.21 mA reaches the optocoupler and 0.092 mA is lost, so an optocoupler chosen for 2 mA nominal will see the right current even at the bottom of the tolerance window.
Two hundred and fifty nanoseconds against a scan cycle
A 250 ns maximum propagation delay is far below any programmable controller scan, so on a normal input the figure only matters for a counter or a position latch that reads the input directly. What it does change is the filter: with this delay the anti-bounce and noise filtering has to be done in the controller, because nothing in the part slows the edge down. That is the opposite trade from an optocoupler front end, where the optocoupler itself is the filter.
Before the order goes out
The test pulse input is the feature that separates this part from a plain optocoupler input, because it lets a controller inject a diagnostic pulse and confirm the whole path is alive without waiting for the field signal to change. The pin to pin cross reference lists the digital input devices that share this 6 lead footprint, the BOM shortage recovery page is where to start when the SOT23 line is short, and the analog and mixed signal category page holds the rest of the interface family.
MAX22191AUT+T: forty eight volt inputs need external resistors, and the type decides the threshold
The device is compliant with IEC 61131-2 Type 1 and Type 3 inputs at 24 V, and the vendor states that 48 V operation is compliant with the addition of external resistors. That sentence is the whole answer to the most common question about this part: the current limiting window of plus or minus 15 percent is what has to be preserved at 48 V, and the external resistor is chosen to burn the extra voltage rather than to change the threshold. A 48 V field supply through the same input without those parts puts the internal limiter outside its window and the part outside its rating.
| Item | Published value | Arithmetic or consequence |
|---|---|---|
| Input range | -60 V to +60 V | A reversed 24 V field wire is inside the range |
| Standards | IEC 61131-2 Type 1 and Type 3 at 24 V | Type 3 needs a higher current at the same voltage, which the limiter sets |
| 48 V use | Compliant with external resistors | The extra voltage has to be dropped outside the part |
| Current limit | Plus or minus 15 percent window | The resistor tolerance enters that window at 48 V |
| Propagation delay | 250 ns maximum | A 1 ms scan cycle is four thousand times longer |
| Quiescent current | 100 uA typical with an optocoupler | Eight channels are 0.8 mA, so a field supply is not needed |
| Temperature | -40 C to +125 C ambient | The 58 mW at 24 V is inside a small body at that ambient |
Type 1 and Type 3 differ in current, not in voltage
Both types switch at 24 V, and the difference is the current the sensor has to source to be recognised, which is why the part has a current limited input rather than a simple comparator. A board that declares Type 3 compliance has to show the current at the low end of the field supply, where a long cable and a 20 percent low supply meet. That is a cable resistance calculation, and it is the reason the 15 percent window appears on the page at all.
The test pulse input is a diagnostic, not a protection feature
The vendor lists a test pulse diagnostic that lets the controller verify the input path without the field device switching, which turns a stuck input into a testable failure instead of a field return. The TVS surge protection described on the page covers the surge, and the diagnostic covers the wire, and the two together are what make a channel diagnosable at the board level. Neither replaces an external fuse on a 48 V rail.
Buying this order code
The AUT suffix is the small body and the plus the reel, and the two part models in the family are different input configurations rather than different grades. The industrial interface family is on the analog line card, optocoupler and isolator partners are compared on the pin to pin page, and the reel is booked through the lead time desk.
Request Quote — In Stock, 100% New & Original, Full Warranty